月別アーカイブ: 2024年3月

    IMG20231102193535
  • Gibson ES-335 フレットすり合わせ

  • 2024/03/13
  • Category:
  • ギブソン製ES-335のフレットすり合わせです。

    消耗でフレット状態が悪く使用が難しい状態です。

    こうした状態でも気にせず使用している人も多いかもしれませんが、音詰まり箇所があると正しく鳴らないポジションが出てくるのでコードの響き等も悪くなります。
    音詰まり箇所がミュートしている様な状態になるので、ギターの場合は周りの人も気が付く位にかなり気になってくると思います。

    フレットをすり合わせ問題無い状態に仕上げました。

    特にギブソン製はフレットの仕上げも悪く上面が台形な事も多い為、綺麗に丸めると音程感も非常に良くなります。
    正直、元状態が良くないので新品でもすり合わせてフレット上面を綺麗に丸めて使用した方が絶対に良いです。

    ありがとうございました♪


    This is a Gibson ES-335 fret grinder.

    The fret condition is poor due to wear and tear, making it difficult to use.

    Many people may not mind using the guitar in this condition, but if there is a clogged fret, the guitar will not sound properly in some positions, and the resonance of chords will deteriorate.
    The clogged fretboard is like a muted sound, and in the case of guitars, people around you will notice it.

    The frets have been worn out and the guitar is now in good condition.

    The frets, especially on Gibson guitars, are often poorly finished and trapezoidal on the top surface, so rounding them off nicely will improve the pitch feel very much.
    To be honest, the original condition is not good, so it is definitely better to use a new one with the top surface of the frets nicely rounded by rubbing it together.

    Thank you very much

    Translated with DeepL.com (free version)


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231003173359
  • YAMAHA LL6 セットアップ

  • 2024/03/12
  • Category:
  • ヤマハ製LL6のセットアップです。

    大きく順反りし弾き難い状態です。

    調整でトラスロッド限界、やや順反りの状態です。
    アコギは当然ながらエレキギターと違い太い弦を使用するので弦を張りっぱなしにしていれば順反りしていくのとプラスしてトップ材が浮いて弦高が高くなっていきます。

    エレキギターも近年は木材が柔らかくなってきているので猶更使用していない時は弦を緩めていないと単純に寿命が短くなるという事になります。

    音が良く、低価格帯には思えないサウンドです。
    ヤマハは低価格帯でも音質が良いアコギが多く、数万円でも人に勧められる個体が多いので購入にお勧めです。
    特にアコギはこうした構造上、強い弦張力でネックもボディもダメになるので完全に消耗品楽器と思っていた方が良いです。
    なのでこうした低価格帯で良い楽器が買えるヤマハは非常に優秀です。
    私も昔は3万円位のヤマハ製アコギをレコーディング等にも使用していました。

    ありがとうございました♪


    This is a Yamaha LL6 setup.

    It is hard to play due to the large forward bow.

    The truss rod is at the limit after adjustment, and the guitar is slightly warped.
    Unlike electric guitars, acoustic guitars use thicker strings, so if the strings are left taut, the strings will bow forward and the top wood will float, making the string height higher.

    The wood of electric guitars has become softer in recent years, so if you don’t loosen the strings when not in use, you will simply shorten the life of the guitar.

    The sound is good and does not seem to be in the low price range.
    Yamaha has many acoustic guitars with good sound quality even in the low price range, and many of them can be recommended to others for tens of thousands of yen, making them a good purchase.
    Especially, due to the structure of acoustic guitars, it is better to think of them as completely consumable instruments, as both the neck and body can be ruined by the strong string tension.
    Therefore, Yamaha is a very good place to buy a good instrument at such a low price range.
    I used to use a Yamaha acoustic guitar for recording and other purposes for about 30,000 yen.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    ギターサムネ
  • Proper storage to prolong the life of your instrument

  • 2024/03/11
  • Category:
  • We are “Draw a New Sound”, running a repair store that is now in its 11th year.

    The current status of musical instruments in Japan is as follows

    I don’t know what the situation is like in other countries, but there are many cases where the strings are left taut, causing a large amount of forward bowing, which exceeds the range of truss rod adjustment and ruins the neck.

    However, it is a questionable environment that many experts in repair stores and music stores other than myself say that it is OK to leave the strings taut. This area is Japanese, but I have never seen anyone other than myself transmitting the message that “strings should be loosened”.

    The neck is not structurally designed to withstand the tension of the strings.

    It may be true that many old woods were strong and did not warp easily even when strings were stretched, but recent woods tend to be weaker and more prone to warp under the tension of strings.

    This is to be expected, as the wood of the past was naturally grown for many years, and the size and density of the wood naturally increased, making it a good quality material. In recent years, however, the artificial use of fertilizers and other chemicals has resulted in a wood that has not grown naturally and is not as dense as it could have been. And trees that have grown naturally for a long time are probably already harvested.

    In addition, the wood is quickly harvested, processed, and commercialized. I think this explains why the strength of the wood is reduced.

    With this background, if you work in a repair store, it is natural to notice a decrease in wood strength when you touch a new instrument every day.

    However, the current state of the Japanese musical instrument industry is that it does not communicate this information, and the people who buy the instruments seem to be creating a cycle in which the instruments are ruined by the buyers themselves, forcing them to buy new ones.

    Information from people like me, who have been working in the field for many years, has become a minority opinion in Japan, and even on Youtube and blogs, it is not seen at all.

    However, every year more and more people cry because the instruments they buy do not last long enough. Many new instruments are sold with little room in the truss rod from the beginning, or are sold in a state where the truss rod is almost at its limit. Such inferior products are increasing, even for famous makers and expensive instruments.

    How about overseas?

    I have been using translation software to send information to English-speaking countries since 2024, but I would like to know if it is the same in other countries or if it is happening only in Japan.

    I would like to know if this is the same thing happening in other countries or just in Japan.

    Musical instruments are wood, so drying them out is especially bad. In the summer, air conditioning dries them out, and in the winter, the outside air is dry, and in addition, the heating system dries out the room, so the use of a humidifier is essential all year round.

    Most instruments often have little room in the truss rod in their current condition. Most guitars and basses are much more likely to have conditions that require loosening the strings.

    If the strings are kept loose and properly humidified, forward warping is unlikely to occur.

    The looseness of the strings is determined by the effectiveness of the truss rod.
    For example, if the truss rod is at its limit, loosen the strings until there is zero tension.
    If the truss rod has a significant excess, the strings should be lowered a half or full tone. In this way, the amount of string loosening is adjusted according to the amount of excess truss rod.

    If the truss rod excess is close to 100%, it is better to leave the strings on only in this case, as you do not want the instrument to warp backwards, but such a good situation is rare. Most instruments are often in a state where the truss rod is quite effective.

    If the strings are loose and warp back, this is a situation to be happy about.
    If the instrument has warped backwards and you have to loosen the truss rod, loosening the truss rod means that the amount of excess has been restored.

    By storing the instrument in this way, it is possible to maintain the same instrument for many years.

    Please protect your precious instrument with proper knowledge.

    Thank you for reading.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231007211338
  • Fullertone STROKE 60 Rusted Fiesta Red ストラトキャスター フレットすり合わせ

  • 2024/03/11
  • Category:
  • フラートーン製ストラトキャスターのフレットすり合わせです。

    消耗で音詰まりしている状態です。

    また6弦サドルのイモネジが錆で固着して調整できない状態の為、紙を挟んで弦高調整をしました。こちらは交換が必要です。

    中古購入なのか素人改造によりリアPUの位相が逆の様子でセンターとのハーフトーンがおかしい状態です。

    すり合わせする事で演奏に問題無い状態に仕上げる事ができました。

    中古購入品は各所にガタが出ている物が多いので、販売側も素人な事も多いので詳しい詳細を出していない事も多いです。
    問題点を全て直す位に考えて購入しないとまともでないギターを購入する可能性が出てきます。

    ありがとうございました♪


    This is a fret grinder for a Fullerton Stratocaster.

    The frets are clogged due to wear and tear.

    Also, the string height adjustment was done by inserting a piece of paper between the 6 string saddle’s imo screws because they are stuck due to rust and cannot be adjusted. This one needs to be replaced.

    The phase of the rear PU seems to be reversed due to amateur modification, and the halftone with the center is not correct.

    We were able to finish it up without any problem in playing by aligning them.

    Many used instruments have rattles in various parts, and the seller is often an amateur and does not provide detailed information.
    If you don’t think about fixing all the problems, you may end up with a guitar that is not in good shape.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231005193516
  • ESP レスポール セットアップ&ジャック交換

  • 2024/03/10
  • Category:
  • ESP製レスポールのセットアップ・ジャック交換です。

    ジャックにガリ、順反りで弦高が高い状態です。

    いくら高額で精度が良いメーカーとしても、調整状態が悪いと弾き難い状態になってしまいます。
    特に精度が高いと順反り具合が大きく感じる(元の状態が良いだけに)ので、意外と作りが良いメーカー程に状態の良し悪しが分かり易いと思います。

    調整しジャックを交換する事で問題無い状態に仕上げる事ができました。

    ありがとうございました♪


    This is a setup jack replacement for an ESP Les Paul.

    The jack is warped and the string height is too high.

    No matter how expensive and accurate the manufacturer is, if the adjustment is bad, it will be difficult to play.
    Especially, if the accuracy is high, the warped strings will be felt more (because the original condition is good), so it is easier to tell if the condition is good or bad as the manufacturer is surprisingly good.

    We were able to finish it up without any problems by adjusting and replacing the jack.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    IMG20231105204002
  • MXR 復刻版Distortion+ DCジャック増設

  • 2024/03/08
  • Category:
  • IMG20231105195912

    MXR製復刻ディストーション+のDCジャック増設です。

    DCジャックの増設です。元々は電池駆動のみの仕様です。

    通常版より音が太めのサウンド。
    軽いシャーシャーとした歪みが良くなっているモデルですので通常版を使っている方はこちらの方がより良い音になります。

    IMG20231105203527

    DCジャックを増設する事によりパワーサプライ等から電源供給もでき他のエフェクターとボードを組む際に都合が良くなります。
    こうした電池のみ駆動のモデルはボードに組んでも交換し易い様に考えたり、考えなくても毎回交換の手間が物凄くなる(ケーブル挿しっぱなしは電池を消耗する為)のでメーカーも当たり前ですが何で最初からDCジャックを付けて販売しないのでしょうか?
    はっきり言いますがメーカーも使用する人の事を考え、時代に合った製品作りをしてほしいです。
    本来ならこうした改造をする必要が無い様にして物を販売してほしい所です。

    どうしても楽器業界が古い体質故に「昔は良かったからこのままでいい」と、全く進化が見られない所があるので上層部を若い人に総入れ替えすると良くなる気がします。

    ありがとうございました♪


    This is a DC jack addition to the MXR Reissue Distortion+.

    This is a DC jack addition. Originally battery-powered only.

    The sound is fatter than the normal version.
    This model has better light shear distortion, so if you are using the normal version, this one will sound better.

    By adding a DC jack, power can be supplied from a power supply or other source, which is convenient when assembling a board with other effectors.
    Even if such battery-only models are assembled on a board, it would be a huge hassle to replace the batteries every time they are replaced (because leaving the cables plugged in drains the batteries), so why don’t manufacturers just add a DC jack from the beginning?
    To put it bluntly, I wish manufacturers would think about the people who use their products and make products that are in line with the times.
    I would like them to sell products that do not require such modifications.

    I think it will be better if the upper management is replaced by young people.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231027183036
  • FenderCustomShop ジャズベース セットアップ

  • 2024/03/07
  • Category:
  • フェンダーカスタムショップ製ジャズベースのセットアップです。

    新品で購入して約1ヵ月との事ですが調整状態が悪く弾き難い状態です。

    順反りして弾き難い状態ですのでトラスロッドを回して反りをストレートにする必要があります。

    触ってみると最初からトラスロッドに殆ど余裕が無く(残りの余り量が90°も回せない程度)、調整でトラスロッドが限界状態となりました。

    こうした高額で有名なメーカー製品でもこの状態なのは珍しくありません。
    結構多くこの様な状態で販売している事が多くあります。

    メーカーも販売側もこの様な状態として分かってて売っているか、もしくは検品等をろくにしておらず知らずに販売しているか、どちらにしても酷いです。

    こうした状態でも弾けるならまだ良いですが、少しでも順反りすると調整で直せないので弾き難くなり、更に順反りすると弦高が高い上に10~12フレットから音詰まりしてきます。楽器としてトラスロッドの調整ができないのは致命的です。
    いわゆる「今は良いかもしれないけど将来は心配な状態、余裕が全く無い状態」です。
    新品で最初からこうですからきっと長持ちしないでしょう。
    ベースの場合は弦張力が強い事もあり今より順反りして数年でダメになる可能性の方が高いと思います。
    世の中にはこの様な状態な物も多くありますが、それでも「弦は張りっぱなしで良い」と言う素人が大勢居る事も業界として危険です。

    楽器屋等でもこうした状態の場合で買い取りの際はトラスロッドが限界や余裕が無い事を理由として安く買い叩かれるでしょう。
    トラスロッド限界等の状態はいわゆるジャンク扱いになる可能性があります。
    そうして安く買い取るのに、売ってる側は何故こうした事を公表して販売していないのか疑問に感じて下さい。

    Youtubeでもブログでも言ってますがこの様な環境を作った消費者側にも問題があります。
    本当に何度も言いますが無知を卒業して下さい。勉強して下さい。

    なので購入時は新品でもトラスロッドの余り量を必ず聞く、トラスロッドの余り量の記載が無いなら必ずその場で回して確認させてもらって購入して下さい。
    その辺りの確認作業を行わないなら買わないで下さい。
    高額な物を買う訳ですから、買う側からしたら当然の権利です。
    この様な事を今まで皆がしていかないから、この様な現状が産まれます。

    新品でもトラスロッドの余り量を表記させる文化を皆様の力で作って下さい。
    そうしない場合、いずれこうした状態で自分が買う様な事になる環境だという事を覚えてて下さい。
    自分の為にもなる事と、状態が悪い物を売れなくなる環境になるので人助けにもなります。

    ありがとうございました♪


    This is a Fender Custom Shop Jazz Bass setup.

    The bass was purchased new and has been in the shop for about a month, but it is in poor condition and hard to play.

    The truss rod needs to be turned to straighten out the warp.

    When we touched it, we found that there was almost no room in the truss rod from the beginning (the remaining amount of room was such that the truss rod could not be turned even 90 degrees), and the truss rod was at its limit after adjustment.

    It is not uncommon to find such expensive and well-known manufacturers’ products in this condition.
    Many of them are sold in this condition.

    Either the manufacturer and the seller know that the product is in this condition and are selling it, or they are not inspecting the product properly and are selling it without knowing it.

    If you can play the instrument in this condition, it is still good, but if it is warped even a little, it becomes difficult to play because it cannot be fixed by adjustment, and if it is further warped, the string height will be high and the sound will become clogged from the 10th to 12th fret. It is fatal for an instrument not to be able to adjust the truss rod.
    It is what is called “a condition that may be good now but is worrisome in the future, a condition with no room at all.
    It will probably not last long because it is like this from the beginning when it is new.
    In the case of a bass guitar, the string tension is so strong that there is a higher possibility that the instrument will warp more slowly than it is now and will be ruined in a few years.
    There are many basses out there in this condition, but the fact that there are still many amateurs who say, “Just leave the strings on,” is also dangerous for the industry.

    Even at a music shop, if you are buying a guitar in this condition, you will probably get a discount because the truss rod is at its limit or there is no room to spare.
    A truss rod at the limit of its capacity may be treated as junk.
    You have to wonder why the seller does not disclose this kind of thing to the public when he/she buys the guitar at such a low price.

    As I have said on Youtube and in my blog, there is a problem with the consumers who have created such an environment.
    I really have to say it again and again, please grow out of your ignorance. Please study.

    When you buy a new guitar, please make sure to ask about the amount of truss rod left, even if it is a new one.
    If you don’t check the amount of truss rod, please don’t buy it.
    It is your right to do so, because you are buying a very expensive item.
    This is the reason why we are in this situation.

    Please help to create a culture that allows people to indicate the amount of truss rod left in a new instrument.
    If you don’t, please remember that this is the kind of environment in which you will eventually end up buying a new instrument in this condition.
    It will be good for you and it will also help others because you will be in an environment where you will not be able to sell items that are in bad condition.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231007175123
  • FenderJAPAN ストラトキャスター エリッククラプトンモデル PU交換&セットアップ FenderCustomShop Fat50’s

  • 2024/03/06
  • Category:
  • IMG20231007170151

    フェンダージャパン製ストラトキャスター、エリッククラプトンモデルのPU交換・セットアップです。

    レースセンサーから交換です。
    クラプトンモデルだがブースターが外され通常のストラトキャスター回路になっている状態です。

    PUはフェンダー製Fat50に交換です。

    交換後は音が硬め、ヴィンテージサウンドというよりはモダン系に近い様な音になりました。
    というよりもレースセンサーが良過ぎる事もあるので、比較となると中々これより良い音になるのは難しいかもしれません。
    むしろシングルコイルPU交換にレースセンサーを選ぶパターンも多いと思います。
    エリッククラプトンも何故にこのPUの使用を辞めたのか謎な位です。

    ありがとうございました♪


    This is a PU replacement and setup for a Fender Japan Stratocaster, Eric Clapton model.

    This is a replacement from a race sensor.
    Clapton model with the booster removed and in normal Stratocaster circuit.

    The PU was replaced with a Fender Fat50.

    After the replacement, the sound became harder and more like a modern sound rather than a vintage sound.
    The sound of the Race Sensor is too good, so it may be difficult to get a better sound than this one.
    I think there are many people who choose the Race Sensor as a single coil PU replacement.
    It is a mystery why Eric Clapton quit using this PU.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231025192645
  • FenderUSA American Performer Jazzmaster 3-Color Sunburst セットアップ

  • 2024/03/05
  • Category:
  • フェンダーUSA製ジャズマスターのセットアップです。

    新品購入にて個人で並行輸入品との事です。通常のブリッジと異なりシンクロトレモロを搭載したジャズマスターです。
    他にもプリセットスイッチが無くなったモデルです。

    初期状態で既にトラスロッドに余裕が少なく順反りを調整したらトラスロッド限界状態になりました。

    実際にこうしたパターンはとても多いので購入時に確認ができるお店じゃないと買ってはいけません。
    今回の件も全然珍しい事ではありません。過去のブログでも多くこの様な状態が出てきます。
    だから弦は緩めて保管しないといけないし、購入時にトラスロッドの使用率をチェックした上で購入しないと寿命が短いギターを買ってしまう形になります。

    検品もろくにできていない証拠でもあるので、そしてこの辺りに詳しく話ができないお店からも買ってはダメです。

    一応は弾けるレベルですがこれから順反りしたら直せませんので、当然ながら弦を緩めて保管しましょう。

    ありがとうございました♪


    This is a Fender USA Jazzmaster setup.

    It is an individual parallel import at new purchase. This Jazzmaster has a synchronized tremolo unlike the regular bridge.
    Other than that, this model has lost the preset switch.

    The truss rod is already at the limit after adjusting the forward warp.

    This kind of pattern is very common, so you should not buy a Jazzmaster unless you can check it when you buy it.
    This case is not at all unusual. We have seen this kind of situation in many of our past blogs.
    So, you need to keep the strings loose and check the usage rate of the truss rod before you buy, or you will end up buying a guitar with a short lifespan.

    It is also evidence that the inspection is not done well, and you should not buy from a store that cannot talk to you in detail about this area.

    The guitar is playable, but if it warps in the future, it cannot be fixed, so of course, loosen the strings and keep it in storage.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar