月別アーカイブ: 2025年5月


    PXL_20250306_124508410
  • Fender / Player Stratocaster Maple Fingerboard ストラトキャスター ナット交換&セットアップ curtis novak pickups

  • 2025/05/13
  • Category:
  • PXL_20250306_112904418

    フェンダーストラトキャスターのナット交換・セットアップです。

    ナット高が非常に高く弾き難い状態で、お客様の要望によりこの機会に溝切りよりも交換する事となりました。

    カーティスノバック製PUに交換です。
    こちらはかなり音質が良く、メンバーシップ限定動画にても紹介しておりますがお勧めです。

    メンバーシップ限定動画ではリペア現場で取り付けたパーツのレビュー等、一般動画で公開していない動画をアップしておりますのでご覧下さい。

    ありがとうございました♪


    This is a nut replacement and setup for a Fender Stratocaster.

    The nut height was very high and difficult to play. At the customer’s request, we decided to take this opportunity to replace the nut rather than cut a groove.

    We replaced the PU with a Curtis Novak PU.
    The sound quality is very good, and as shown in the membership-only video, it is highly recommended.

    Please check out our membership-only videos, which include reviews of parts installed at the repair site and other videos that are not available to the general public.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250223_090001566
  • FenderJAPAN テレキャスター PU交換&セットアップ

  • 2025/05/12
  • Category:
  • フェンダージャパン製テレキャスターのPU交換・セットアップです。

    メーカー不明だがお客様持ち込みPUに交換しました。

    フロントは明るめで音抜けが良く、リアは硬く無く音の分離も良いサウンドです。

    90~2000年代フェンダージャパン製と思いますがトラスロッドも多少は余りがあり、音も良く良好個体です。

    フレットの消耗が凄いのですり合わせした方が良い状態ですので正しく使用したくなりましたらすり合わせをお勧めします。

    ありがとうございました♪


    This is a PU replacement and setup for a Fender Japan Telecaster.

    The PU was replaced with a PU brought in by the customer, though the manufacturer is unknown.

    The front is bright and has good sound, and the rear is not hard and has good sound separation.

    The truss rod has a little extra room and the sound is good.

    The frets are very worn and should be grated.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250315_083839319
  • Ibanez RG460DX-ROM Roadster Orange Metallic RG セットアップ

  • 2025/05/11
  • Category:
  • アイバニーズ製RG460DXのセットアップです。

    新品で購入したが音詰まり箇所があり調整に持ち込まれました。

    状態を確認すると4フレットで音詰まりが発生しており、5フレットだけ高い状態で4フレットが音詰まりする状態です。

    新品でもこうした不具合があるまま平気で販売されている事があるので、購入前に店員にチェックさせて買うのは当然ですがお店側が素人だと不具合に気が付きません。

    酷いお店だと初期状態の弦高が高く、弦高を高くすれば不具合箇所が誤魔化されるので音詰まりが分かり難くなります。
    なので弦高が高い時点で疑った方が良いです。
    購入後に指摘しても「当店での基準はこの弦高で不具合が出なければ問題無いと判断してます。」と誤魔化されて終わりです。

    不具合箇所が分かれば新品なら1年保証等が付いているので、基本は早い方が良いですが不具合を発見した際は購入店に申し出て直してもらいましょう。

    ただし相手が素人過ぎるとこうした圧倒的に誰でも分かる不具合ですら店員が不具合を分からない現象が起きて対応してくれない事が出てきます。
    実際にこの個体はリピーターのお客様のギターの為、後日に別のギター持ち込み時にお客様からこのギターは初期不良で返品した報告を聞いた際の購入した楽器店のやり取り話を聞きました。

    この音詰まりする状態でも楽器店側は「メーカーが送ってきた状態なので、状態は基準の範囲で問題無い」との事や「他リペアショップでチェックさせても構わない」とまで言われたそうです。
    ちなみにギター本体はお店に送ってあり店員が確認した状態での連絡です。そのやり取りメールも確認しました。

    私のお店でチェックした事はお客様が購入店に伝えてなかったそうですが、楽器店側の素人さがここまで来てると買うのが危険なレベルになっています。
    この個体はそこまで高額なモデルではありませんが、万が一高額なモデルを購入してアフターサービスがここまで酷いと楽器は楽器屋で買う事が難しくなってきます。

    楽器屋で買う際も基本的に知ってほしい知識としてちゃんと調整した上で渡してもらう事、トラスロッドの余り量を確認させる事、そもそも新品でトラスロッドの余り量を表示しないなら買わない事、不具合が起こった場合はどの様な対応をするのか必ず確認する事です。

    今回は何度もメールのやり取りの上でやっと返品できたレベルとの事で、明らか商品に不具合があるのに返品する事すら困難という事例をお客様から見せてもらいました。

    楽器屋をやってる人達へ向けて、もう少し自分の仕事にプライドを持って下さい。
    金儲けしか考えていないならこの仕事を辞めて下さい。業界として害悪な存在です。
    人が泣いて金を儲けてるなら仕事としてのやり方が完全に間違っています。
    良い仕事をして喜ばせた対価としてお金を稼いで下さい。

    ありがとうございました♪


    This is a setup for an Ibanez RG460DX.

    It was purchased new but brought in for adjustment due to a jammed part.

    The condition of the guitar was confirmed to be clogged at the 4th fret, with only the 5th fret being high and the 4th fret being clogged.

    It is natural to have the store staff check the guitar before buying it, but if the store is an amateur, they will not notice the problem.

    If the shop is not a good store, the initial string height will be high, and if the string height is high enough, the defect will be disguised, so it will be difficult to recognize the sound clogging.
    Therefore, it is better to be suspicious when the string height is high.
    If you point this out after purchase, you will be misled and end up saying, “Our standard is that if there is no problem at this string height, we judge that there is no problem. If you point out the problem after purchase, you will end up being misled.

    If you find a problem, it is better to report it to the store where you purchased the instrument and have it fixed.

    However, if the store is too much of an amateur, there may be a phenomenon that the store staff does not understand the problem, even if the problem is overwhelmingly obvious to anyone else, and they may not be able to fix it.
    In fact, this guitar belongs to a repeat customer, and I heard a story about an exchange at the music store where the customer brought in another guitar and later heard a report that this guitar had been returned due to initial defects.

    Even with this clogged condition, the music store said that the condition was within the standard range because it was sent by the manufacturer, and that they were even willing to let another repair store check it out.
    Incidentally, the guitar itself was sent to the store and the store staff checked it. I also confirmed the email exchange.

    I heard that the customer did not tell the store of purchase that he had checked it at my store, but the amateurishness on the part of the music store has reached such a level that it is dangerous to buy it.
    Although this unit is not that expensive model, if you buy an expensive model and the after-sales service is this bad, it will be difficult to buy a musical instrument at a music shop.

    When buying from a music shop, the basic things you need to know are that you should have the instrument adjusted properly, that you should check the amount of truss rod left, that you should not buy a new instrument if it does not show the amount of truss rod left, and that you should always check what they do in the event of a problem.

    In this case, the customer told us that he was able to return the instrument after many emails, and that he found it difficult to return the instrument even though the product was obviously defective.

    To those who are in the music store business, please have a little more pride in your work.
    If all you care about is making money, get out of the business. You are a detriment to the industry.
    If you are making money by making people cry, you are doing your job completely wrong.
    Please do a good job and make money in return for pleasing people.

    Thank you.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    ギターサムネ
  • 本当に正しいセットアップは「順反り・若干順反りで調整する事」なのか?

  • 2025/05/09
  • Category:
  • 度々お客様から聞かれる質問として「楽器屋や他店リペアショップでは順反り・若干順反りで調整した方が良いと聞くのですが、どうなのですか?」と聞かれたりします。

    まず世の中の正しい情報を確認する事として「一人だけから情報を得る事は危険」である事を知りましょう。
    私の発信にも同じ事が言えますので、私に対しても疑いの姿勢で見てもらって問題ありません。
    ハッキリ言える事として情報を得る事は大事ですが、情報をインプットしたら必ず確認作業(自分の楽器で試す等)をして実際に試して確認して下さい。

    大半の人達はアウトプットしてないから知識が無く、出てくる情報に簡単に騙されるのです。
    情報を得て「本当かどうか分からない」の段階に来たのなら後は簡単、自分で試せば良いだけ。簡単な話です。
    そんな簡単な事をしてないから騙され続けます。

    楽器関係で情報を出している人の特徴として「これが正義で他は間違っている」と善悪二元論で表すパターンが非常に多く、例えば「弦を緩めるか緩めないか?」もそうですが楽器状態を実際に確認しそこに合わせて行う作業な事にも関わらずそうした条件を全て度外視して「弦は緩めないで良い」という人達ばかりです。
    その証拠に弦を張りっぱなしで良いと言う人達はその理由を具体的に説明できません。
    大体は毎日弾くなら問題無いと言ったりしますが、例えばネックが柔らかく反り易い・既にトラスロッド限界状態等の楽器だったらどうするの?等、そうした細かく各個体の状態に合わせた保管方法等を説明してる人は私以外に見た事がありません。

    何か一点だけを強調し「正義と悪」の様に単純表現した方が分かり易く、ハッキリ言うと客側の多くが無知で騙され易い知識レベルなので有名な人が言うだけでその言葉を信じる人が大半なので自分で自分の楽器をダメにしているので情報を正しく判断できないし確認もしない消費者側が悪い所です。
    まずは消費者側、客側が悪いという意識を持って下さい。

    ~セットアップは順反りで行うべきか?~

    簡単な話です。ネック反りを順反り状態でセットアップしてみて下さい。

    自分が気に入ればOK、気に入らないならNGです。

    簡単な話です。
    この状態を「何故お前が決めてるんだ?」って話です。
    ただの「好みの問題だろ!」って事が正解です。

    何故こうした表現をしている所が多いのかはどこか1点を切り取ってそれを正義に見せた方が客が分かり易く洗脳し易く自分の商売がやり易いからです。

    順反りが良いとする人の理屈として「弦振動の振幅する範囲を考え、弦振動のスペースを取る為には順反りさせた方が良い」という理屈は正しいです。
    正しいのですが、これが「ギターベースを弾く人全員に当てはまる答えなのか?」が完全に抜け落ちています。

    当然ながら弦高がメチャクチャ低い状態が好みの人も居るでしょう。
    右手の力が弱く、弦を弾いて発生させる弦の振幅範囲が狭い人も居るでしょう。

    この辺りの人達を完全に削除した考え方になります。

    当然ながら順反り状態が良い人(弦高が高い人)も居る事でしょう。
    では正しい状態は何なのか?簡単です。
    その人が好む調整状態に仕上げる事が正解です。簡単な話でしょ?
    正しい調整状態は弾く人が決める事です。

    ~分からないなら猶更やってもらうべき~

    良く分からないなら様々なお店にお金を払っていろんな調整状態を体験して下さい。

    当たり前ですが勉強には「お金」が必要です。他にも自分で知識を付けて試す方法もありますが金を払って専門家にやってもらった方が早いです。

    結局は経験値であり、良い状態って感覚も人それぞれにあるので自分が良いと思う状態を探し当てないといけません。

    受け身はダメ、簡単にネットで聞くのもダメです。自分の楽器で確認して下さい。

    ネックの僅かな反り具合でも弾き心地は大きく変わりますし、弾き心地は良くても音が微妙な事もあるのでその弾き心地と音質バランスの好みを知る必要があります。

    この辺りの基準が分からないといつまで経っても一部が強調されたネット情報に騙され続けます。

    本当に正しい知識を紹介すると私の記事の様に長く複雑で様々な要因を紹介する事になるので、理解するにも知識が必要になり多くの方は1回読んですぐには理解できない内容になります。
    人は簡単な事に流れ、怠けたい生き物ですから完全に商品を売る側はその人間心理を突いて商売をしてきている事に気が付いて下さい。

    また「被害者意識」も今すぐ辞めて下さい。
    「私は素人だから」と言って楽をしてはいけません。
    今は調べたら専門家の解説へすぐに行き着く事ができますし、この記事に行き着いているなら他の記事も読んで学べばこの程度の内容は簡単に理解できます。
    つまり理解できないのはあなたの責任です。
    時間が掛かっても知識を得ようと行動してればいずれ理解できるようになるし自分がギターを買う際に失敗しない目利きが付く等して役に立てる所まで知識が付きますが、最初から「素人だから分からない」というスタンスならば成長しませんしどこかで痛い目を見てもそれはあなたが勉強しなかった事への責任です。
    そうした何も行動しない素人が犠牲になっているのが楽器業界の消費者です。

    ~結論~

    順反り状態でセットアップが良いのか悪いか?は自分でやってみて弾いて確認して決めて下さい。

    順反りさせるという事は弦高が高くなり弾き難くなります。
    弾き難く感じるかも人それぞれですから、また順反りと言葉にしてもその反り具合は言葉では表せられません。

    ネックの反りを真っ直ぐにすれば弦とフレットの平行具合が殆ど全体的に同じになるのでどこを押さえても弾き易いと感じるでしょう。
    ただ弦の振幅具合を考えると、弦が完全に鳴り切らない事となりますがエレキギターでそこまで考えた調整にする必要があるのか?と考えるプレイヤーも多いはずです。
    アコギだったら分かるけど、音よりも弾き易さを優先した方が良いと思う人やかなり歪ませたり速弾きしたい人にそこまで重要な要素なのか?等の基準はプレイヤーで大きく感覚が違います。

    結論として実際に触ってみてプレイヤーの答えが大きく異なるはずなので、調整の形として一つだけが正しくなる事は絶対にあり得ません。
    そう言ってる人はただのポジショントーク、自分を良く見せようとしてるだけです。
    少し考えたら上記の説明通りでおかしな話だなを分かるはずです。
    調整の良し悪しは人によって大きく違います。
    そこをコミュニケーションを取りプレイヤーの好みに合わせていくのが正しい調整方法です。

    知識は必ず必要になります。
    それと同時に自分で確認して学ぶ事も必要になります。
    騙されず正しい情報を得る為に。
    コスパ・タイパと言ってたらバカになるだけです。
    そうした人が増えた方が商売上有利なので利用されない様に勉強して下さい。

    ありがとうございました♪


    One question I am often asked by customers is, “I hear from music shops and other repair stores that it is better to adjust a forward or slightly forward warp.” What do you think?

    First of all, you should know that “it is dangerous to get information from only one person” as a way to confirm the correct information in the world.
    The same thing can be said about my communications, so there is no problem if you look at me with an attitude of skepticism.
    I can clearly say that it is important to obtain information, but after inputting the information, be sure to check it (e.g., by trying it out on your own instrument) and actually try it out to confirm it.

    Most people don’t have the knowledge because they don’t output the information, and they are easily deceived by the information that comes out.
    If you have reached the stage of “I don’t know if it’s true or not” after getting information, the rest is easy, just try it out yourself. It’s that simple.
    You continue to be deceived because you have not done such a simple thing.

    One of the characteristics of people who provide information on musical instruments is that they often use a dualistic view of right and wrong, saying that “this is right and the other is wrong,” and that “to loosen or not to loosen strings? For example, when it comes to “whether to loosen or not to loosen strings,” they are always saying “don’t loosen the strings,” disregarding all such conditions, despite the fact that it is a task that must be done after checking the condition of the instrument and adjusting it to the actual condition.
    As proof, those who say it is fine to leave the strings on cannot give a concrete reason why.
    For example, what if the neck is soft and easily warped, or the truss rod is already at its limit? I have never seen anyone other than myself explain in such detail how to store each individual instrument according to its condition.

    It is easier to understand if you emphasize only one point and describe it simply as “right and wrong.” To put it clearly, most of the customers are ignorant and gullible, and most of them believe what famous people say just because they say so. This is the consumer’s fault.
    First of all, please be aware that the consumer and customer side is at fault.

    It’s simple. Try setting up the neck warp in the forward warp state.

    If you like it, it’s OK, if not, it’s not.

    It’s that simple.
    Why are you deciding? I say, “Why are you deciding?
    It’s just a matter of taste! is the correct answer.

    The reason why many places use this kind of expression is because it is easier for customers to understand, easier for them to be brainwashed, and easier for them to do business with you if you cut out one point and make it look like you are doing it justice.

    The logic of those who say that forward bending is better is correct: “Forward bending is better for taking up space for string vibration, considering the range of amplitude of string vibration.
    This is correct, but the question “Is this an answer that applies to all guitar bass players?” is completely missing. is completely missing.

    Of course, there are those who prefer a very low string height.
    Some people may have a weak right hand and the range of string amplitude generated by plucking the strings may be narrow.

    This approach completely removes these people from the equation.

    Of course, there will be those who prefer forward warp (high string height).
    So what is the correct state? It is simple.
    The correct answer is to adjust the strings to the person’s preferred state of adjustment. Simple, isn’t it?
    The correct adjustment is decided by the player.

    If you are not sure, pay money to various stores to experience various adjustment states.

    Of course, you need “money” to learn. There are other ways to gain knowledge and try it yourself, but it is faster to pay an expert to do it for you.

    In the end, it is all about experience, and each person has their own sense of what is a good state, so you have to find the state that you think is good.

    Don’t be passive, and don’t simply ask on the Internet. Check with your own instrument.

    Even a slight warp of the neck can make a big difference in playing comfort, and even if it feels good, the sound can be subtle, so you need to know what you like about the balance between playing comfort and sound quality.

    If you do not know the standards in this area, you will continue to be deceived by information on the Internet, which emphasizes only some aspects.

    If you really want to introduce the correct knowledge, you will have to read a long and complicated article like mine, which will introduce various factors, and you will need knowledge to understand it.
    People are creatures that want to be lazy, and the sellers are trying to take advantage of this human psychology.

    Is the setup good or bad in the forward warped state? Please try and play it by yourself to confirm whether it is good or bad.

    If the strings are bowed forward, the string height will be higher and it will be more difficult to play.
    It depends on each person whether it is difficult to play or not, and the degree of warp cannot be expressed in words.

    If the neck is straight, the parallelism between the strings and frets will be almost the same all over, so it will feel easy to play no matter where you press the strings.
    However, considering the amplitude of the strings, the strings will not fully sound. Many players may wonder if it is necessary to make such adjustments on electric guitars.
    I can understand if it is an acoustic guitar, but is it really that important for those who prioritize playability over sound, or for those who want to distort the sound or play fast? The criteria for this differ greatly from one player to another.

    In conclusion, players’ answers must be very different when they actually touch it, so it is absolutely impossible for one form of adjustment to be correct.
    Those who say so are just position talk, trying to make themselves look good.
    If you think about it for a moment, you will see that it is just as I explained above, which is crazy.

    Knowledge is always necessary.
    At the same time, you need to check and learn for yourself.
    To get the right information, not to be deceived.
    If you say “cosmetics,” “cosmetics,” and “typa,” you will only become a fool.
    The more people who do so, the better for business, so please learn not to be taken advantage of.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    ギターサムネ
  • クルミラ加工した電源プラグ・イヤホンプラグをオーディオでの使用した音質変化

  • 2025/05/08
  • Category:
  • PXL_20250321_084552793

    クルミラ加工したマリンコ電源プラグを使用した音質変化はYoutubeやブログで効果が分かった事と思います。

    今回は~オーディオでの使用レビューです。

    クルミラ加工したノイトリック製ステレオプラグを使用しモガミ3106を製作しPCオーディオでのケーブルを交換してチェックします。

    使用する工房のスピーカーはエクリプスTD-M1です。

    まず3106の使用ですが、元のケーブルがコードカンパニーSERSEN+フルテック CF-735SM-N1のケーブルです。

    ケーブルを交換してみた感想ですが、明らか以前より全体的に音が良くなります。

    製作したケーブル自体の値段はクルミラ加工を除けば安価な物で、パーツ代だけだと3mで2000円程度です。
    コードカンパニーとフルテックで製作したプラグは2mで約15000円程度です。

    クルミラ加工をしたケーブルは単純に高域と低域の音質が耳障りが良い音に変化します。

    音の分子が整う性質が音質を良くする働きは楽器よりもオーディオの方が分かり易いと思います。

    ●左右差の音質が整う気がする●

    またTD-M1の片側から片側へプラグでスピーカーを接続する端子があり、そこもクルミラ加工したノイトリック製プラグに交換すると音質の左右差があまり出なくなった様に思います。

    乗せてる土台が違うので音が変わると思いますが、それでも接続する側(プリアンプが搭載されていない側)の音が弱く感じていたのですがその感覚が無くなった(正確には差が小さくなった)様に思います。

    ●明らか高域・低域のレンジが変わる●

    高域がしっかり伸びる(音がコモらない)し耳に痛くない高域になります。
    低域は強過ぎない(柔らかい)音に変わり、むしろ以前よりも低域が出ている様な音に変化しますがブーミーではなく心地良い低音です。

    TD-M1は「低域が出ない」と言われているが、出ていないのではなく元の低域がクリアだからかもしれないです。
    他のスピーカーと比べ元から音に歪みが発生せず低音がクリアな事から雑味が少なく、それが普段から歪んだ音に慣れた人が聴けば低音が削れて聴こえると思います。

    クルミラ加工したスピーカーケーブルだと足りないと思う低音が増えて聴こえ、バランスが良く聴こえる様になると思います。

    ●クルミラ加工電源プラグも複数使用するのはあまり大きな効果を感じない。●

    2~3個で充分に思いました。
    以前の改質コンセントの実験はブログでも詳細を書きましたが銀メッキなので、沢山使う事でクルミラ加工の影響とは別に銀メッキ効果も増えて音が変化(良くも悪くも)するので繋げ過ぎは良くない印象でした。
    今回は非メッキである事もあり、繋げ過ぎて音が悪くなる事は感じず、繋げ過ぎるとある程度から効果を感じなくなるだけと思います。

    PC本体の方が効果が大きい(以前のレビューと同じ)のは変わらずで、再生する側にクルミラ加工したプラグの影響が大きい様に思います。

    ●令和の虎でやってた内容に似てる●

    5月1日に放送された「令和の虎」でスピーカーを売る回があったのですが、かなり勉強になる回でした。

    スピーカーの構造で音を良くする事が、クルミラ効果で同じ様な効果が得られると思います。

    スピーカーも音が良い本体を作るには様々な研究が必要で、かなり手間を掛けて本当に良いスピーカーが作られます。

    その音が良いスピーカーの音をクルミラ加工したプラグはパーツ単体で同じ様な効果を与える事から凄い効果と思います。

    スピーカーの場合はパーツや内部構造で音自体の波形を整えリッチな音質にする訳ですが、クルミラの場合は電子の粒を整え音をリッチにするので形は違いますが出てくる音は似た効果に思いました。

    正確には自分で紹介されたスピーカーを実際に聴く必要がありますが、動画の内容で自分が実験した感想と同じ様な事を言っており勉強になりました。

    ●終わりに●

    これら実験から楽器よりもオーディオの変化の方が分かり易いかと思いました。

    楽器と同じでオーディオも音は好みですが、オーディオの場合は明らか欠点らしい所が見つからないので元の音を良くしたい目的なら確実にクルミラ加工パーツは使用する事で良くなると思います。

    次にモガミ2497ケーブル自体のクルミラ加工を頼んでいる為、クルミラ加工プラグ+クルミラ加工ケーブルを使用すればより良くなる事と思います。
    ただケーブルの場合は内部にクルミラ加工を吸着できないので(既に完成している状態では)、ケーブルの外面にクルミラ加工を加えても効果が出るのか?までは不明ですがまずは実験としてやってみるとの事ですので届き次第試してまたレビューを投稿していきたいと思いますので楽しみにしていて下さい。

    ありがとうございました♪


    You have probably seen the effect of the sound quality change using the Kurumira processed Marinco power plugs on Youtube and on our blog.

    This time – a review of its use in audio.

    We will use Neutrik stereo plugs with Kurumira processing to create the Mogami 3106 and replace the cables with PC audio cables.

    The speaker of the workshop used is Eclipse TD-M1.

    First of all, the 3106 is used, but the original cable is a cord company SERSEN + Furutech CF-735SM-N1 cable.

    After replacing the cable, it is clear that the overall sound is better than before.

    The price of the cable itself is inexpensive, except for the Kurumira processing, and the cost of the parts alone is about 2,000 yen for 3 meters.
    The plug made by Cord Company and Furutech costs about 15,000 yen for 2m.

    Cables with Kurumira processing simply change the sound quality of high and low frequencies to a grating sound.

    I think it is easier to understand how the molecular arrangement of sound improves the sound quality in audio than in musical instruments.

    I feel that the sound quality of the left-right difference can be improved.

    There is also a terminal to connect a speaker with a plug from one side of the TD-M1 to the other, and when I replaced it with a Neutrik plug that has been treated with Kurumira, the left-right difference in sound quality seemed to have decreased.

    I think the sound is different because the foundation on which the speakers are mounted is different, but I still felt that the side to which the speakers are connected (the side without the preamplifier) sounded weaker, but this feeling has disappeared (or more precisely, the difference has become smaller).

    The range of the high and low frequency range is clearly different.

    The high frequency range is extended well (the sound is not flat), and the high frequency range is not painful to the ear.
    The low frequency range is not too strong (soft), and the sound is not boomy but pleasant.

    TD-M1 is said to have “no low frequency,” but it may be because the original low frequency is clear, not because it does not have low frequency.
    Compared to other speakers, there is no distortion in the sound from the original and the bass is clear, so there is less clutter, which is why people who are used to distorted sound usually hear the bass as sharpened.

    If you are used to distorted sound, you may hear the bass sound reduced.

    I don’t feel that using multiple Kurumilla-processed power plugs has much of an effect. I don’t feel that using more than one Kurumira-processed power plug is very effective.

    I thought 2 or 3 plugs were enough.
    I wrote about the details of my previous experiments with modified power outlets in my blog, but since they are silver-plated, I had the impression that using too many of them would increase the silver-plating effect and change the sound (for better or worse), apart from the effect of the Kurumira processing, so it would not be good to connect too many of them.
    This time, I did not feel that the sound became worse due to too much connection, partly because it is non-plating, and I think that if you connect too much, you will not feel the effect from a certain degree.

    The effect on the PC itself is still the same (same as the previous review), and I think the Kurumira plug has a large effect on the side that plays the music.

    This is similar to what was shown on “Tiger of 2025.

    On May 1, there was a segment on selling speakers on “Tiger of 2025,” and it was quite informative.

    I think that improving the sound through the structure of the speaker will have a similar effect to the Kurumilla effect.

    Speakers also require a lot of research to make a good sounding body, and a lot of time and effort is put into making a really good speaker.

    The Kurumilla plugs that have been processed to produce the sound of a speaker with a good sound are a great effect because they give the same effect as a single part.

    In the case of speakers, the waveform of the sound itself is adjusted and made richer by the parts and internal structure, but in the case of Kurumilla, the electron grains are adjusted and the sound is made richer, so I thought the sound that came out was similar to the effect in a different form.

    I need to listen to the speakers introduced in the video myself to be precise, but I learned a lot from the video, which was similar to my impression from my own experimentation.

    At the end of the day

    From these experiments, I thought it would be easier to understand the changes in audio than in musical instruments.

    As with musical instruments, the sound of audio equipment is a matter of taste, but in the case of audio equipment, I could not find any obvious defects, so if the purpose is to improve the original sound, the use of Kurumira processed parts will certainly improve the sound.

    Next, since the Mogami 2497 cable itself has been ordered with Kurumira processing, the use of a Kurumira-processed plug + Kurumira-processed cable will improve the sound even more.
    However, in the case of the cable, it is not possible to adsorb Kurumira processing inside (in the already completed state), so I am not sure if adding Kurumira processing to the outer surface of the cable will have any effect. I am not sure until I receive the cable, but they are going to try it as an experiment first, so I will try it as soon as I receive it and post a review again, so please look forward to it.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250426_094959314
  • Squier by Fender Classic Vibe 60s Stratocaster セットアップ

  • 2025/05/07
  • Category:
  • Youtubeでも紹介しましたスクワイヤー製クラシックヴァイヴ60年モデルストラトキャスターのセットアップです。

    2025年製の新品です。
    こちらの個体は特に初期状態でも不具合が無く、調整初期状態も他メーカーと比べ良かったです。
    トラスロッドの余り量も充分にあり良好な個体でした。

    調整してみると弾き易く、何よりも音が良い事が驚きです。
    約6万円のモデルですがサウンド面では高価格帯と大きくは変わらないと思います。

    ナット高も低めで弾き易く、フレットサイドの処理も低価格帯としても丁寧な部類です。
    音質も良いとなれば低価格帯ではかなり勧められますね。

    詳細についてはYoutubeにも動画を上げておりますので参考下さい。

    ありがとうございました♪



    This is a Squier Classic Vibe ’60 Stratocaster setup as featured on Youtube.

    It is brand new, made in 2025.
    There were no problems with this one, especially in the initial state, and the initial state of adjustment was better than other makers.
    There is enough truss rod left over and it is in good condition.

    After adjustment, it was easy to play and the sound was amazingly good.
    It is a 60,000 yen model, but in terms of sound, I think it is not much different from higher-priced models.

    The nut height is low, making it easy to play, and the fret side treatment is also very well done, even in the low price range.
    The sound quality is also good, which is highly recommended in the low price range.

    For more details, please refer to the video on Youtube.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250210_082856097
  • Gibson USA SG ネック割れ修正

  • 2025/05/06
  • Category:
  • PXL_20250209_104508836

    ギブソン製SGのネック割れ修正です。

    ヘッドの接着面に亀裂が入っている状態、3Pマホガニーネックです。
    特に割れも酷い状態ではないのでそのまま使用していても問題無さそうですが、要望により接着する事となりました。

    また配線にミスがある様でセンターでフェイズアウトする状態です。

    古い年代製に多い事ではありますがこちらはトラスロッドの効きがおかしいです。
    内部のトラスロッドに不具合がありそうで調整後に弦高が変わる(反りの状態が変わる)ので、内部でのトラスロッドの引っ掛かりが悪い様子です。
    ある程度触っていると落ち着いてきますが、状態としては不安でしかありません。
    こうした状態は最悪トラスロッドが効かなくなる事もあるので、作りが悪いメーカー品を購入するという事はこうした不具合が起こってくる事も理解しないといけません。

    こうしたメーカーがある事から「トラスロッドを一気に回したら壊れる」という間違った知識が広まっています。
    トラスロッドを回した事が悪いのではなく、回しただけで壊れる様な作りをしている事が問題です。
    当然ながらこうした事がリペアで私が触って起きたとしても責任を取る事は致しません。
    メーカーの問題なのと、こうした知識を持っていないお客様の問題です。
    そうしたトラブルにならない様に理解して購入した方が良いです。

    ありがとうございました♪


    This is a Gibson SG neck crack fix.

    The head has a crack on the gluing surface, and the neck is made of 3P mahogany.
    The crack is not so bad, so it seems to be OK to use it as it is, but we decided to glue it back together by request.

    Also, there seems to be a mistake in the wiring and it phases out at the center.

    The truss rod is not working properly, as is often the case with older models.
    The internal truss rod seems to be defective, and the string height changes after adjustment (the state of warping changes), so the truss rod is not hooked properly inside.
    It will settle down after some touching, but the condition is only uneasy.
    In the worst case scenario, the truss rod may stop working, so it is important to understand that purchasing a poorly made product from a manufacturer can lead to this kind of problem.

    Because of the existence of such makers, the false knowledge that “turning the truss rod all at once will break it” is widespread.
    The problem is not that turning the truss rod is bad, but that the truss rod is made in such a way that it can be broken just by turning it.
    Of course, I will not take responsibility if such a thing happens when I touch the truss rod for repair.
    It is the manufacturer’s problem and the customer’s problem who does not have such knowledge.
    It is better to buy with understanding to avoid such problems.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250201_093434840
  • JAM Pedals Fuzz Phrase DCジャック交換&電池スナップ交換

  • 2025/05/05
  • Category:
  • ジャムペダル製ファズフレイズのDCジャック交換・電池スナップ交換です。

    DCジャックにガリがあり、電池スナップ破損で交換する事となりました。

    古い年代製のファズを再現したモデルになります。

    現行品でも似たモデルが購入できる様子ですがデザインが異なったり内部の回路も異なる様子です。
    こちらはジミヘンモデルの様ですが通常版のモデルもある様子です。

    ありがとうございました♪


    This is a DC jack replacement and battery snap replacement for a Jam Pedal Fuzz Flaze.

    The DC jack has a buzz and the battery snap is damaged and will be replaced.

    This model is a reproduction of an old vintage fuzz.

    Similar models are available in the current market, but they have different designs and internal circuits.
    This one looks like the Jimi Hendrix model, but there is also a regular version available.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE