月別アーカイブ: 2026年2月


    PXL_20250725_120223109
  • Gibson レスポール ブリッジ交換 MONTREUX ABR-1 style Bridge non-wired relic

  • 2026/02/27
  • Category:
  • ギブソン製レスポールのブリッジ交換です。

    サドルが取れて紛失したとの事で、この機会に新しいブリッジへ交換です。

    ギブソン製純正のサドルに交換ですが、これは溝切りされていないのでパーツ代にプラス溝切り料金が加わるので料金面ではGOTOH製等がお勧めです。

    しかしGOTOH製と比べ音が違う気がして、こちらの方が音が柔らかいと思います。

    GOTOH製は金属が硬いのか、その分丈夫ですが音が硬くなります。
    こちらの純正サドルは音が柔らかい傾向ですがサドル自体にガタがあるので精度は悪いです。

    Gibsonユーザーは分かると思いますがサドルにガタがあり弦振動で暴れて変なノイズが発生したりします。
    金属も柔らかいからかオクターブ調整ビスも使用していると歪みが出てしまい、オクターブ調整によってガタ具合が変わったりします。
    音以外のデメリットは大きいので要注意です。

    ありがとうございました♪


    Replacing the bridge on a Gibson Les Paul.

    The saddle came off and was lost, so we’re taking this opportunity to replace the entire bridge.

    We’re replacing it with a genuine Gibson saddle, but since this one isn’t pre-slotted, the cost includes both the part and the slotting fee. For cost reasons, we recommend GOTOH or similar brands.

    However, I feel the sound differs compared to GOTOH; I think this one produces a softer tone.

    GOTOH saddles, perhaps due to the harder metal, are more durable but produce a harsher sound.
    These genuine saddles tend to have a softer tone, but they have some play in the saddle itself, so precision is poor.

    Gibson users will understand—the saddle wobbles, causing strange noises from string vibration.
    Perhaps because the metal is softer, the octave adjustment screws also warp with use, and adjusting the octave changes the amount of wobble.
    The drawbacks beyond sound quality are significant, so be cautious.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20251230_073305024
  • Navigator Les Paul Custom レスポールカスタム 配線直し&セットアップ SEYMOUR DUNCAN SH-55n Seth Lover Gibson P.A.F

  • 2026/02/26
  • Category:
  • ナビゲーター製レスポールカスタムの配線直し・セットアップです。

    お客様持ち込みのフロントPUにセイモアダンカン製SH-55、リアにGibsonの80年代PAFを付けた状態です。

    配線がベルデンのヴィンテージ配線、コンデンサにバンブルビーの組み合わせです。

    フロントは音が甘い傾向だが音抜けが良く、リアはバーストバッカー1より柔らかくやや出力がある感じです。

    古い年代製のPUは磁力落ちの影響で音が柔らかくなるので、現行品にも同じ物があると比べたらハッキリと音の違いが分かるかと思います。

    ありがとうございました♪


    Wiring rework and setup for a Navigator-made Les Paul Custom.

    The customer-supplied front pickup is a Seymour Duncan SH-55, and the rear is a Gibson 80s PAF.

    Wiring uses Belden vintage wire paired with Bumblebee capacitors.

    The front pickup has a sweet tone but excellent projection, while the rear feels softer than a Burstbucker 1 with slightly more output.

    Older pickups tend to have softer tones due to magnetic field decay. Comparing them to current models with the same model number should clearly reveal the tonal difference.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20251224_094809450
  • vanzandt ストラトキャスター 配線直し&セットアップ ブレンダー回路

  • 2026/02/25
  • Category:
  • ヴァンザンド製ストラトキャスターの配線直し・セットアップです。

    またお客様の要望でリアのトーンを250kΩから500kΩにしてみたいとの要望で交換しました。
    スイッチポットを使い、フロントPUを混ぜるブレンダー回路になりました。

    トーンでも250KΩから500kΩになるとコモる範囲が減り、微調整の幅が広がる印象です。
    ボリュームポットのKΩを変えて音を変える方法は定番ですが、トーンでもサウンド変化が起こります。

    ブレンダー回路はセンター+リア時のポジションでONにすると、フロント+リアの他にPU3つを鳴らす事も可能になり新しいストラトに産まれ変わります。

    ブレンダー回路も近年の定番改造になってますので、まだ知らない人は試した方が良いでしょう。

    ありがとうございました♪


    Wiring rework and setup for a Vanzand Stratocaster.

    Also, per the customer’s request, we replaced the rear tone pot from 250kΩ to 500kΩ.
    Using a switch pot, it now functions as a blender circuit mixing the front pickup.

    Changing the tone pot from 250kΩ to 500kΩ seems to reduce the range of muddiness and expand the scope for fine-tuning.
    Changing the KΩ rating of the volume pot to alter the sound is a classic method, but changing the tone pot also produces sound variations.

    With the blender circuit, when switched ON in the Center + Rear position, it allows all three pickups to sound simultaneously, in addition to Front + Rear, effectively reborn as a new Strat.

    The blender circuit has become a standard modification in recent years, so if you haven’t tried it yet, it’s worth giving it a shot.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20251212_115051528
  • MOTU UltraLite mk3 Hybrid 配線直し

  • 2026/02/24
  • Category:
  • モツ製ウルトラライトMk3ハイブリッドの配線直しです。

    電源が入らない状態です。
    この個体は電源トラブルが非常に多いので、中古等は消耗により特に壊れ易い状態になっていると思います。

    内部をチェックしてみると電源部の基盤が繋がっていない(過去にも同じ事あり)状態でした。

    急に基盤が死ぬ?のも不思議なのですが実際に通電しなくなっているので事実です。
    配線を引き回し、通電不良個所を配線で繋げて無事に動作する様になりました。

    こちらもエフェクターと同じ扱いで作業の保証はございませんが内部を確認して直そうと対応する事は可能です。

    ありがとうございました♪


    Repairing the wiring on a Motsu Ultra Light Mk3 Hybrid.

    It won’t power on.
    This particular unit has had numerous power issues, so I suspect used ones are especially prone to failure due to wear and tear.

    Checking inside revealed the power section’s circuit board wasn’t connected (this has happened before).

    It’s odd for a board to suddenly die, but it’s a fact that it stopped powering up.
    I rerouted the wiring, bridged the faulty connection points, and got it working properly again.

    Like with effects pedals, there’s no warranty on this work, but I can inspect the internals and attempt repairs.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20251224_123652674
  • EDWARDS E-FR-145GT セットアップ&ジャック交換

  • 2026/02/23
  • Category:
  • エドワーズ製フォレストのセットアップ・ジャック交換です。

    大きく順反りしてかなり弦高が高い状態です。

    その他にジャック消耗で音が途切れる状態ですので新品に交換しました。

    正しく調整する事で弾き易い状態に仕上げる事ができました。

    ありがとうございました♪


    Edwards Forest setup and jack replacement.

    The neck was significantly bowed backward, resulting in excessively high string action.

    Additionally, the worn jacks were causing intermittent sound dropouts, so they were replaced with new ones.

    Proper adjustment has restored playability to an optimal state.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20251212_093634886
  • Fullertone ストラトキャスター ピックガード交換&配線直し&詳しい状態診断&ナット溝切り調整&セットアップ K&T

  • 2026/02/22
  • Category:
  • PXL_20251210_101552212

    PXL_20251209_085113826.MP

    フラートーン製ストラトキャスターのピックガード交換・配線直し・ナット溝切り調整・セットアップです。
    加えて詳しい状態診断です。

    K&T製のモデル年代は不明ですが中古品PUに交換、ヴィンテージベルデン配線にて組み込みです。

    ナット高が1~3弦だけ高めな状態を削って直しました。

    トラスロッドの余り量も多く良好個体で、何年製かは不明ですが良好個体です。
    調整した状態から1周程度はトラスロッドの余りがあります。

    モッサリ感ある古い年代製のサウンドに仕上がりました。

    ありがとうございました♪


    Flatone Stratocaster pickguard replacement, rewiring, nut slot adjustment, and setup.
    Includes detailed condition assessment.

    Model year unknown K&T model, fitted with used pickups and vintage Belden wiring.

    The nut height was adjusted by shaving down the excess height on strings 1 through 3.

    The truss rod has ample adjustment range remaining, indicating a well-maintained instrument. While the exact year of manufacture is unknown, it is in excellent condition.
    After the adjustments, there is still about one full turn of truss rod adjustment left.

    The result is a sound characteristic of an older, more vintage-feeling guitar.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    PXL_20251230_094940287
  • BOSS HM-2 Heavy Metal トラブルチェック&修正

  • 2026/02/20
  • Category:
  • ボス製MH-2のトラブルチェック・ガリ修正になります。

    ツマミのガリ、ボリュームはガリが酷く箇所により音が出なくなる状態です。

    中身をチェックしてみるとポットが特殊な物、背が低く基盤に付いているので現行品で交換不可でした。
    ポットを交換する場合は基盤を外し、ポットに配線を引き回す改造をしなくてはいけませんので高額になってしまいます。

    洗浄剤で対処し直しましたが再発する様であれば買い直しか上記の修理になります。

    普段は電池での使用との事ですが電池スナップも動かすと電源が途切れたりしますが、極端に指で動かさなければ大丈夫な状態です。
    古い年代製なだけに各所の消耗が目立ちます。
    またDCで電源が入らない状態、DCジャックが壊れていると思うがテスターチェックにてジャック部は通電はしており原因不明です。DCジャックも独自規格パーツにより交換不可です。

    現状は電池使用で問題無い事、修理の際は高額になってしまう(中古で買った方が明らか安い)ので古い年代製のエフェクターは壊れない様に大事に使用する事をお勧めします。

    ありがとうございました♪


    Troubleshooting and scratchy sound correction for Boss MH-2.

    The knobs have scratchy sound, and the volume control is severely scratchy, causing sound loss in certain areas.

    Upon checking the internals, the potentiometers are specialized, low-profile types mounted directly to the circuit board, making replacement with current parts impossible.
    Replacing the potentiometers would require removing the circuit board and rewiring the connections to the potentiometers, resulting in a high cost.

    We reapplied cleaning solution, but if the issue recurs, either repurchase or the above repair will be necessary.

    It’s usually used with batteries, but moving the battery snap can cause power loss. However, it’s fine as long as you don’t move it excessively with your fingers.
    Being an older model, wear and tear is noticeable in various areas.
    Additionally, it won’t power on via DC. We suspect the DC jack is broken, but tester checks show the jack itself is conducting power, so the cause is unknown.

    Currently, battery operation is problem-free. Repair would be costly (clearly cheaper to buy used), so I recommend handling older effects pedals with care to prevent damage.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20251120_132246619
  • ThornTree ストラトキャスター ピックガード交換&配線直し&セットアップ LINDY FRALIN REAL 54 Set White

  • 2026/02/19
  • Category:
  • PXL_20251120_120620303

    ソーンツリー製ストラトキャスターのピックガード交換・配線直し・セットアップです。

    ピックガードを交換しポット交換2箇所・コンデンサ交換、PUをリンディフレーリンのリアル54に交換です。

    こちらはスイッチでPUを制御する仕様となるので、フロントとリアのハーフトーンや3つ全てONのサウンドも使用できる状態になります。

    音の粒が綺麗に鳴り、コード感も良いです。
    どのポジションも音が良く、スイッチ切り替えなので瞬時には難しいですが全体的に良いサウンドです。

    ありがとうございました♪


    Pickguard replacement, rewiring, and setup for a Thorn Tree Stratocaster.

    The pickguard was replaced, two potentiometers and a capacitor were swapped out, and the pickups were upgraded to Lindy Fralin Real 54s.

    This setup uses a switch to control the pickups, enabling half-tone sounds from the front and rear pickups, as well as a full-on sound from all three pickups.

    The tone is clean and crisp, with excellent chord definition.
    Every fret position sounds great. While instant switching between sounds might be challenging, the overall sound quality is superb.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE