カテゴリー別アーカイブ: リペア

    IMG20240329214153
  • DEAN ML フロイドローズ難点修理&セットアップ

  • 2024/07/11
  • Category:
  • IMG20240328201411

    IMG20240329160149

    IMG20240328202236

    ディーン製MLのフロイドローズ難点修理・セットアップです。

    今回はフロイドローズで起こるトラブルが多数起きた状態の修理です。

    メルカリで購入したとの事ですがかなり状態が悪く、当然ながらこれら状態は知らされていないとの事です。

    スタッドブッシュ抜けにより弦を張ると弦高が上がってくる(当然アームを使うのはNG)、ナイフエッジ消耗でチューニングが不安、サドルの弦をロックするビス山が壊れて弦が張れない状態です。
    ビス部は確実に素人作業で壊した物ですね。

    ナイフエッジの消耗は基本的に起こります。弦を張りっぱなしが良くないのはネックだけでなくこうしたパーツの高負荷部分にも同じ事が言えます。
    弦を張る事自体が大きな負荷なので、それら負荷が常に消耗させている意識を持ちましょう。
    弾いていない時に無駄に消耗させている行為です。

    スタッド部は弦を張る方向に強い力が掛かるので、斜め方向に穴が広がって抜けてきます。これも長年の消耗で起こる症状です。
    これも弦を緩めて保管する事で長持ちさせれます。
    ただし今回の場合は例外で、新品時点で最初からガバガバだった可能性があります。
    スタッド部の穴に塗装が乗っており、穴も変形が見られない事から最初から抜ける位の穴で空いていた様子で非常に精度が悪いです。
    2本とも手の力で抜く事ができました。
    こちらは値段も含めて相談し、接着で仕上げる事となりました。

    壊れているサドルは手持ちのフロイドローズモデルのサドル2個を交換して対処しました。
    あくまで応急処置の様な物で後から純正パーツに交換する必要があります。
    また他のサドルも怪しい感じなのでフロイドローズ本体を交換した方が良いです。

    ただフロイドローズも現在は販売が安定しておらず、見つけても凄い値上がりでびっくりする値段になっています。

    今後はフロイドローズ付きギターを購入する際は注意が必要です。
    パーツが入手できない・パーツが高額に悩まされると思います。

    これでアームも使用できて問題無く弾ける状態に仕上げる事ができました。

    ありがとうございました♪


    This is a Floyd Rose difficulty repair and setup for a Dean ML.

    This repair is for a condition that caused many of the problems that occur with Floyd Rose.

    The owner of the instrument purchased it from Mercury, but it was in a very bad condition, and of course he was not informed about these conditions.

    The stud bushings are missing, causing the string height to rise when the strings are stretched (naturally, using an arm is not an option), the knife-edge is worn out, making tuning insecure, and the screw threads that lock the strings on the saddle are broken, making it impossible to stretch the strings.
    The screw part was definitely broken by amateur work.

    Knife-edge wear is a common occurrence. It is not good to leave the strings on the neck, but the same can be said for these highly stressed parts.
    Stringing itself is a big load, so be aware that these loads are constantly causing wear and tear.
    When you are not playing, you are wasting energy.

    The studs are subjected to a strong force in the direction of stringing, which causes the holes to widen and come loose in a diagonal direction. This is another symptom of wear and tear over the years.
    This can also be prolonged by loosening the strings and storing them.
    However, this case is an exception, and it may have been a governor from the beginning when it was new.
    The paint was on the stud holes, and the holes were not deformed, so it seems that the holes were made to the point where they could be pulled out from the beginning, which is very inaccurate.
    I was able to pull out both studs by hand.
    After discussing the price and other details, we decided to glue them back together.

    The broken saddles were replaced with two Floyd Rose model saddles that we had on hand.
    This is just a stopgap measure and will need to be replaced with genuine parts later.
    The other saddles also look suspicious, so it is better to replace the Floyd Rose itself.

    However, sales of Floyd Rose are not stable at the moment, and even if you can find one, the price has gone up dramatically and the price is astonishingly high.

    In the future, be careful when purchasing a guitar with a Floyd Rose.
    I think you will suffer from unavailability of parts and high cost of parts.

    Now I can use the arm and make it ready to play without any problems.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240218203506
  • FenderUSA 90年代 テレキャスター セットアップ

  • 2024/07/09
  • Category:
  • フェンダーUSA製90年代テレキャスターのセットアップです。

    消耗が凄く全体の状態が悪いが何とか使えるレベルです。相当使いこまれていますね。

    ナット高が消耗で音が詰まり気味、フレットの消耗が全体的に凄い、電装が交換されている様で内部状態が悪いので一度全てリペアが必要な個体です。

    トラスロッドの効きも悪く、調整でトラスロッド限界となりました。

    フェンダー系で多いので気を付けて確認しないといけない事はトラスロッドの効き具合です。
    効きが悪い個体も多いので、そうした個体はトラスロッドの余り量が多くても殆ど回しても反りが直らないので実質トラスロッドの余裕が無い事になります。
    順反りを直しただけでトラスロッドが限界になる事も多いので、長持ちする個体を選ばないと泣きを見ると思います。

    ありがとうございました♪


    This is a Fender USA 90’s Telecaster setup.

    It has a lot of wear and tear and is in poor overall condition, but manageable. It has been used quite a bit.

    The nut height is worn out and the sound is a bit stuck, the frets are worn out, the electrics have been replaced, and the internal condition is poor, so the whole unit needs to be repaired once.

    The truss rod is not working well, and the truss rod has reached its limit after adjustment.

    The truss rod is not working well, so we have to be careful to check it.
    There are many fenders with poor truss rod effectiveness, so even if the truss rod has a large amount of excess, the warping will not be corrected even if the truss rod is turned almost all the way, which means there is practically no room for the truss rod.
    In many cases, the truss rod will reach its limit just by fixing the forward warp, so if you don’t choose a long-lasting one, you will have a hard time.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240210175721
  • Squier ストラトキャスター Eシリアル国産 ナット溝切り調整&セットアップ

  • 2024/07/08
  • Category:
  • スクワイヤー製ストラトキャスターのナット溝切り調整・セットアップです。

    古い日本製のEシリアルになります。この頃は低価格帯でも良い個体が多かったですね。

    トラスロッドを回してみると効きがあまり良くない個体ですが、年代を考えたら状態は良い方です。

    ナットが別のナットを移植している?のか、溝にRがあるタイプだが全く合っていないのを加工して付け直し、それでもナット高が非常に高いので削って直しました。

    チョーキングで音詰まりする箇所があります。Rがキツイとチョーキングで音詰まりは起こりますがハイポジションのフレット状態が良くないです。
    すり合わせした方が良い状態です。

    PUがプリボラ1967に交換されているとの事で音が良くハーフトーンも良いサウンドです。リアが程好いパワーがあり使い易いストラトです。

    ありがとうございました♪


    This is a Squier Stratocaster nut groove cut adjustment and setup.

    It is an old Japanese E serial. There were many good ones in the low price range at that time.

    The truss rod is not very good, but considering the age, it is in good condition.

    The nut is transplanted from another nut? The nut was transplanted from another nut, or perhaps it was a type with a radius in the groove, but it did not fit at all, so it was modified and reattached.

    There is a part where the sound clogs up when choking, and if the R is too tight, the sound will clog up when choking, but the high position frets are not in good condition.
    It is better to grind them together.

    The PU has been replaced with a Prevola 1967, so the sound is good and the halftone is good. The rear has good power and is easy to use.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240309173005
  • epiphone elite ES-335 セットアップ

  • 2024/07/07
  • Category:
  • エピフォンエリート製ES-335のセットアップです。

    何故か弦高がかなり低い状態により音が詰まる状態です。

    大体の楽器屋では弦高が高く弾き難い上に不具合箇所を見つけ難い状態になっている事が多いのですが、これはその逆パターンです。
    恐らくまともにチェックせず渡したと思います。

    調整する事でまともに弾ける状態になりました。

    エピフォンは箱物が良いモデルが多いので、本家ギブソンでなくても良かったりするパターンがあります。
    近年は精度も低くなってきておりますので購入時は細かく見る必要があるので要注意です。

    ありがとうございました♪


    This is a setup for an Epiphone Elite ES-335.

    For some reason, the string height is quite low and the sound is stuck.

    Most music stores have a high string height which makes it hard to play and hard to find any defects, but this is the opposite.
    This is the opposite case.

    After some adjustments, the instrument is now in a state where it can be played properly.

    Epiphone has many models that are good in the box, so there is a pattern that it is good even if it is not the original Gibson.
    The accuracy has been getting lower in recent years, so please be careful when you buy one, because you need to look at it closely.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240302173051
  • FenderUSA ジャズベース セットアップ

  • 2024/07/05
  • Category:
  • フェンダーUSA製ジャズベースのセットアップです。

    大きく順反りしハイポジションに音詰まりが起きている状態です。

    順反りは限度を超えると弦高が高く弾き難くなる他にハイポジションで音が詰まってきます。
    この辺りはトラスロッドの調整でネックを真っ直ぐにする事で直す事ができますが、トラスロッドの余りが無い場合は対処不能となります。

    調整したら見違える程に弾き易くなりました。

    電送系がバルトリーニPUとXTCTの組み合わせに変更されており音も良いです。

    バルトリーニの様に世間ではマイナーなPUは非常に良く、これが標準で搭載されていない事も業界の闇を感じます。
    簡単に音が良くなっては困るのか、気が付いた人は得をするPUです。

    ありがとうございました♪


    This is a Fender USA Jazz Bass setup.

    The bass has a large forward bow and is clogged in the high position.

    If the forward warp is exceeded, the high string height will make it difficult to play, and the high position will also jam the sound.
    This can be fixed by adjusting the truss rod to straighten the neck, but if there is no extra truss rod, it is impossible to fix the problem.

    After the adjustment, it became easier to play than before.

    The electric transmission system has been changed to a combination of Bartolini PU and XTCT, and the sound is good.

    I feel the darkness of the industry that a minor PU like Bartolini is very good and this is not installed as standard.
    I don’t know if it should be easy to improve the sound, but those who notice it will benefit from this PU.

    Thank you very much… ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240227204928
  • Squier日本製JVシリアル ストラトキャスター ナット交換

  • 2024/07/04
  • Category:
  • スクワイヤー製の古い日本製年代、JVシリアルストラトキャスターのナット交換です。

    ナットが消耗で開放弦が音詰まり、順反りさせて無理矢理使用している状態です。

    全体のフレット消耗が凄いが音詰まりは無いので相談にて保留となりました。

    ナットを交換し問題無い状態に調整できました。

    ナット・フレットは楽器にとって非常に大事な部分です。
    ここに問題があると楽器としてかなり性能ダウンする箇所となりますので消耗を感じたら早い段階で直す事をお勧めします。

    ありがとうございました♪


    This is a nut replacement for an old Japanese vintage, JV serial Stratocaster made by Squier.

    The nut is worn out and the open strings are jammed, forcing the guitar to be used in forward warp.

    The fret wear was very severe, but the sound was not clogged, so we decided to hold off on the consultation.

    We were able to replace the nut and adjust the instrument to a problem-free state.

    Nuts and frets are very important parts of an instrument.
    If there is a problem with this part, the performance of the instrument will be considerably degraded.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240302184652
  • Strandberg Boden7 日本製 セットアップ

  • 2024/07/03
  • Category:
  • ストランドバーグ製Boden7のセットアップです。日本製のモデルです。

    順反りしており弾き難い状態です。

    調整し弾き易くなりましたがトラスロッドに余裕が無い状態です。
    特殊なネックグリップ形状・ヘッドレスのモデルでネック状態がどうなってくるのか、まだ新しいメーカーな事もあり時間が経たないと分からない所ですが通常の楽器と同じく弦張力で順反りしていくのは変わらないと思います。

    特に特殊なネックグリップ形状により、ネック強度の一定率が悪いと思うので反りだけでなくウネリにも繋がりそうです。
    この辺りはもっと時間が経ってデータが集まってくると思います。

    ネック強度も高そうに感じるのですがこの場合はトラスロッドの余り量が少ないので緩めるのは当然として余り量が多かったら緩めないで良いか?とずっと弦を張りっぱなしで問題無いか?と言われたら将来どうなるのか分からないので弦は緩めておいた方が基本無難です。
    弦を緩めてさえいればリスクが無くなるので、ただ面倒なだけで高額な楽器が長持ちする事を考えたなら普通にやれる作業でしょう。

    ありがとうございました♪


    This is a Boden7 setup made in Strandberg. This model was made in Japan.

    It is hard to play due to the forward bow.

    The truss rod has been adjusted to make it easier to play, but there is no room in the truss rod.
    The neck grip is a special neck grip shape and headless model, so it will be hard to tell how the neck condition will change over time, but I believe that it will warp in the same way as a normal instrument.

    In particular, due to the special neck grip shape, the neck strength may not be consistent, which may lead to not only warping but also swelling.
    I think more time will pass and more data will be gathered in this area.

    I feel that the neck strength is also high, but in this case, the truss rod has a small amount of excess, so it is natural to loosen it, but if there is a large amount of excess, is it OK not to loosen it? And is it OK to leave the strings taut all the time? If so, it is basically safer to leave the strings loose because you don’t know what will happen in the future.
    As long as the strings are loosened, there is no risk, so it is just a hassle, but if you think about the longevity of an expensive instrument, it is a task that can be done normally.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240202203954
  • Gibson レスポール ピックガード取り付け&セットアップ

  • 2024/07/02
  • Category:
  • ギブソン製レスポールのピックガード取り付け・セットアップです。

    ピックガードが付いていないモデルの為、お客様持ち込みのピックガードを取り付けました。

    大きく順反りしており弾き難い状態です。

    ネック折れが直されている個体、トラスロッドの効きが変で違和感がある状態です。

    調整で直せましたがトラスロッドの不安があります。

    ギブソンはトラスロッドの仕込みが悪く、内部のロッドT字が引っ掛かりが悪いのかナットを締めてると抜けてくる物がたまにあるので注意です。

    ありがとうございました♪


    This is a pickguard installation and setup for a Gibson Les Paul.

    This guitar does not have a pickguard, so we installed a pickguard brought by the customer.

    The guitar is in a hard-to-play condition due to the large forward bow.

    The neck was broken and the truss rod was not working properly.

    The truss rod could be fixed by adjustment, but there is some concern about the truss rod.

    The truss rod is not well set up, and the rod T-joints inside the truss rod may not catch properly, or it may come out when the nut is tightened, so please be careful.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240204193456
  • FenderJAPAN ジャズベース 配線直し

  • 2024/07/01
  • Category:
  • フェンダージャパン製ジャズベースの配線直しです。

    古い電装パーツを新品へ全交換しました。

    中古品で消耗してある電装パーツは交換して使用する事をお勧めします。

    劣化は単純に音が悪くなりますので、古い物は交換した方が良いでしょう。

    交換後は音が明らかに太くなりました。

    劣化してくるとパワーに係わる低音が削れていくので、消耗すればする程に音が細くなっていきます。

    微々たる変化ですので気が付かないかもしれませんが、古い物から新品へ交換するとかなり大きな変化に感じますので、知らない人は変化に驚くと思います。

    ありがとうございました♪


    This is a rewiring of a Fender Japan Jazz Bass.

    All old electrical parts have been replaced with new ones.

    We recommend replacing used electrical parts that are worn out.

    Deterioration simply makes the sound worse, so it is better to replace old parts.

    After replacement, the sound is noticeably thicker.

    As the parts deteriorate, the bass, which is related to power, will be cut off, and the sound will become thinner as it wears out.

    The change is so slight that you may not notice it, but if you replace the old one with a new one, you will be surprised at the change because it seems like quite a big change.

    Thank you very much♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240217174011
  • Gibson ES-333 セットアップ

  • 2024/06/30
  • Category:
  • ギブソン製ES-333のセットアップです。

    大きく順反りしており弾き難い状態です。

    調整してみると音が良い個体です。

    ギブソンは箱物の方が音が良い個体が多いので、レスポール等は個体差が大きく面白いかもしれませんが良い個体を見つけるのも大変です。

    また裏パネルが付いてるモデルなので電装品の交換が楽なモデルです。
    335等も同じ様な仕様になれば良いんですけどね。

    ありがとうございました♪


    This is a Gibson ES-333 setup.

    It is hard to play as it is heavily forward warped.

    It is an individual with good sound when it is adjusted.

    It is very difficult to find a good one, but it is interesting to see the difference of Les Paul.

    Also, this model has a back panel, so it is easy to replace the electrical components.
    I wish 335 and other models had similar specifications.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE