カテゴリー別アーカイブ: リペア

    IMG20240105203715
  • VOX V847 モデファイ

  • 2024/05/24
  • Category:
  • VOX製V847のMODです。

    今回の内容はトゥルーバイパス化・LED増設・安物ジャックを交換・配線の一部交換です。

    VOXの現行品は中身がどんどん安物になっていき、元から低価格なワウペダルですが現在の現行品は昔と中身が異なります。
    ただ最初からDCジャックが付く様になっている所だけは良いポイントです。

    どうしても音痩せが気になるのであればトゥルーバイパス化がお勧めです。ON/OFFを多用するエフェクターですのでバイパス時の音は気になってくると思います。

    後はONなのかOFFなのか見て分からないのでLEDを追加する等。

    ワウペダルは必要な人には必須なエフェクターなだけあってこうした改造で大きな変化に感じると思います。

    18V化等は音がクリアになりますが、9Vの音が好きという人も居ますのでこの辺りは好みです。

    ありがとうございました♪


    This is a VOX V847 mod.

    The modification includes true bypass, additional LEDs, replacement of cheap jacks, and partial wiring.

    The current VOX products are getting cheaper and cheaper, and although they were originally low-priced wah pedals, the current products are not the same as the old ones.
    The only good point is that the DC jack is attached from the beginning.

    If you are concerned about the sound, we recommend you to use true bypass.

    You can also add an LED to the wah pedal so you can’t tell if it’s on or off.

    Wah pedal is an essential effect pedal for those who need it, so I think you will feel a big change by such modification.

    I think that this is a big change. 18V will make the sound clearer, but some people like the 9V sound, so it is up to you.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231227175528
  • スクワイヤー ムスタング トグルスイッチ交換&セットアップ

  • 2024/05/23
  • Category:
  • スクワイヤー製ムスタングのトグルスイッチ交換・セットアップです。

    トグルにガリがあるので交換しました。

    ハイゲインなPUに交換されています。
    弁当箱ザグリなのですが注意点としてシングルコイル弁当箱ザグリにハムバッカーは入らない場合があります。

    弁当箱ザグリもただ広い20mm程度のザグリが掘られただけの場合や、ハムバッカーが付く事を想定して端側が深く掘られている場合の2種類があります。
    この端が深く掘られていない場合はハムバッカーの耳が干渉したり長いビスが干渉してPUを低く取り付けできない事やピックガードが閉まらない場合が出てきます。

    ビスを短く改造したりザグリを掘り足したりする必要があるので気を付けましょう。
    ピックガードを無理矢理削ってハムバッカーを付けた様な状態になっておりますが、ピックガードだけでなくザグリもハムバッカーが入る様に加工が必要です。

    セットアップしてみると弾き易いモデルです。

    スクワイヤーは値段も安く、中には音が良い物もあるので値段やメーカーで判断しない方が良い代表です。

    ありがとうございました♪


    This is a toggle switch replacement and setup for a Squire Mustang.

    The toggle has been replaced because it has a buzzing sound.

    The PU has been replaced with a high-gain PU.
    The PU was replaced with a high gain PU.

    There are two types of Bento Box Counterbores: one is just a 20mm wide counterbore, and the other is a deep counterbore on the end side for a humbucker to be attached.
    If the ends are not deeply dug, the ears of the humbucker may interfere, or long screws may interfere, making it impossible to install the PU low, or the pickguard may not be able to close.

    It may be necessary to shorten the screws or dig a counterbore to close the pickguard.

    Once set up, this model is easy to play.

    Squier is inexpensive and some of them have good sound, so it is better not to judge by price or manufacturer.

    Thank you very much… ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240118175902
  • Line6 Relay G10 DCジャック増設

  • 2024/05/22
  • Category:
  • IMG20240118171153

    ライン6製ワイヤレス、RelayG10のDCジャック増設です。

    こちらは本当にメーカーが壊れる様に作っている様にしか思えないワイヤレスです。
    正直、購入は避けた方が良いでしょう。

    このUSB電源が壊れ易く、恐らくこの記事を検索で辿り着いたなら同じトラブルでここに来た事でしょう。
    過去にも同じトラブルを直した物もありますが、何度も抜き差しする状態での使用はお勧めしません。
    ボード等に固定し、基本は動かさない様にしないとこのUSB部分が弱いので簡単に破損して使用できなくなります。

    お客様の方で無理矢理ケースを開けようとして周りが傷だらけになっている状態です。
    自分で作業は無理と判断し、こちらに依頼されました。

    また5V電源なので注意が必要で、エフェクターの9Vではございませんので注意が必要です。

    穴を空けてDCジャックを増設しUSBを排除、元のアダプタを使用して動作も問題無く行える様になりました。
    動作も確認OKです。

    こうした改造は保証ができませんが、メーカーは最初から壊れ難い電源で作ってほしいと思います。
    壊れ易い構造で販売するのはどうなんだろう?思います。
    安物ならOKなのですが、それなりの値段する物ですからね。

    ありがとうございました♪


    This is a DC jack addition for a RelayG10 wireless made by Line 6.

    This is a wireless that really seems like the manufacturer is making it to break.
    Frankly, it is best to avoid purchasing this product.

    The USB power supply is fragile and if you came across this article in a search, you probably came here with the same problem.
    We have fixed the same problem in the past, but we do not recommend using it in a situation where it is plugged in and unplugged repeatedly.
    If you do not fix it to the board and basically do not move it, the USB part is weak and can easily be damaged, making it unusable.

    The customer tried to forcibly open the case and the surrounding area is covered with scratches.
    The customer decided that he could not do the work by himself and asked us to do it.

    Also, please note that this is a 5V power supply and not the 9V of an effector.

    We made a hole and added a DC jack, eliminated the USB, and used the original adapter to make it work without any problems.
    The operation is also confirmed OK.

    I can not guarantee this kind of modification, but I hope that the manufacturer will make a power supply that is hard to break from the beginning.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240119193226
  • Proco Turbo RAT フットスイッチ交換

  • 2024/05/21
  • Category:
  • Proco製ターボラットのフットスイッチ交換です。

    ON時の音が非常に小さく、恐らくフットスイッチ不良です。

    フットスイッチはよくON/OFFしたり多用すれば壊れ易いパーツとなります。
    また体重を掛けて踏む人が居ますがこうした事も破損の原因になります。

    交換しましたが内部が交換し難い構造です。

    メーカーは消耗パーツを交換し易い様に作っていてほしい所です。

    ありがとうございました♪


    This is a foot switch replacement for a Proco turbo rat.

    The sound when turning on is very low, probably due to a defective footswitch.

    Foot switches are easily broken if they are turned on and off frequently or used a lot.
    Also, some people step on the foot switch with their weight on it, which can also cause damage.

    The inside of the footswitch is difficult to replace.

    I wish the manufacturer would make the consumable parts easy to replace.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240108182000
  • dragonfly オーダーギター ポット交換

  • 2024/05/20
  • Category:
  • ドラゴンフライ製オーダーメイドギターのポット交換です。

    ボリュームのガリで音が出なくなるとの事で交換しました。

    内部をチェックしてみると配線状態が荒く、周りの配線にハンダコテを当てた様な跡がありました。
    中古購入との事なので中身が素人イジりされている様子です。

    中古品は見えない所に難がある事が多く、販売店でもそこまで丁寧にチェックしている事も少ないので要注意です。

    今回はお客様の要望でボリュームの交換のみです。順反りしていて弾き難い状態です。

    ありがとうございました♪


    This is a pot replacement for a custom made guitar by Dragonfly.

    The pot was replaced because the volume was rattling and sound would not come out.

    When we checked the inside of the guitar, we found that the wiring was in rough condition and there were marks around the wiring that looked like soldering iron had been applied to the wiring.
    Since it was purchased second-hand, the inside of the unit had been tampered with by amateurs.

    Second-hand products often have defects in places that cannot be seen, and even dealers do not always check them that carefully, so be careful.

    This time, we only replaced the volume at the customer’s request. It is hard to play because it is warped.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231230184059
  • Gibson Robot Guitar SG 配線チェック

  • 2024/05/17
  • Category:
  • ギブソン製SGの配線チェックです。

    ロボットギターと呼ばれるオートチューナーが付いたモデルです。

    音が小さくなるとの事で持ち込まれました。

    配線は問題無さそうですが各所にガリがあるので洗浄剤で対処しました。
    各所チェックしてみるとギター本体に問題は無く、使用しているシールドケーブルに問題がありそうです。

    ペグがバッテリー式により、消耗しているのかそこまで電池が持たない様子です。
    電池が切れたら手で回せば良いと思いがちですが回しても動きが遅く、引っ掛かりがある様なので手作業で巻けないペグがあります。

    壊れたら普通のペグに交換されている事が理解できました。
    便利に見えてかなり不都合なペグに思います。

    ありがとうございました♪


    This is a wiring check of a Gibson SG.

    It is a model with auto tuner called “Robot Guitar”.

    It was brought in because the sound was getting quieter.

    The wiring seems to be OK, but there are some scuffs in various places, so we used a cleaning agent to fix them.
    The guitar itself is fine, but the shielded cable used seems to be the problem.

    The pegs are battery operated and the batteries do not seem to last that long.
    I tend to think that I can turn the pegs by hand when the battery runs out, but they move slowly when turned, and there are pegs that cannot be wound by hand because they seem to have a snag.

    I understood that when they break, they are replaced with ordinary pegs.
    I think the pegs look convenient but are quite inconvenient.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231220175643
  • FenderUSA エリッククラプトン ストラトキャスター ポット交換&ジャック交換&セットアップ

  • 2024/05/16
  • Category:
  • フェンダーUSA製ストラトキャスター、エリッククラプトンモデルのポット交換・ジャック交換・セットアップです。

    ポットにガリがある状態です。
    ストラトキャスターはボリューム可変をよく使用すると思いますので消耗も他のギターより早くなります。

    また新品購入のギターとの事ですがポットのビス山が痛んでナットが締め付けができない状態にもなっていました。
    年々組み込みも荒くなっている様です。

    ジャックにもガリがあるので交換しました。

    こうしたアクティブ回路搭載のギターは内部配線も初期状態でかなりぐちゃぐちゃになっており、トラブルが多いギターでもあります。
    基盤も単体で販売されておりますが下手な組み込みが原因で破損してる事も考えられるので、トラブルが起きた際はパーツを新品に全交換するか通常のストラトキャスター配線(パッシブにする等)しても良いかもしれません。
    こちらでもアクティブ回路のモデルは保証ができませんので、メーカーの製造精度に難がある以上は使用する側にもその理解がないとダメです。

    ありがとうございました♪


    This is a Fender USA Stratocaster, Eric Clapton model with pot replacement, jack replacement and setup.

    The pots have some galling.
    Stratocaster guitars are often used with variable volume, so they wear out faster than other guitars.

    The pot screw threads were damaged and the nuts could not be tightened.
    The build quality seems to have gotten rougher over the years.

    The jack also had some buzzing, so we replaced it.

    Guitars with active circuits like this are prone to problems because the internal wiring is messed up in the initial state.
    The circuit board is sold separately, but it may have been damaged due to poor installation, so you may want to replace all the parts with new ones or do normal Stratocaster wiring (passive, etc.) if you have any problems.
    We cannot guarantee the active circuit model here either, so as long as the manufacturer’s manufacturing accuracy is not good, the user must have that understanding.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231114204453
  • YAMAHA FG-180 フレットすり合わせ&ナット溝切り調整

  • 2024/05/15
  • Category:
  • ヤマハ製FG-180のフレットすり合わせ・ナット溝切り調整です。

    古いモデルですが過去にフレット交換されており状態が良くなっている様子ですがその後弾き込まれた大きな消耗により状態が悪くフレットの大きな消耗、ナット高が高い状態です。

    フレットをすり合わせ、高いナットを切って弾き易く仕上げる事ができました。

    ヤマハのFGシリーズは低価格帯ながら音質が良い物が多く、流石に近年の中古で手に入る物は状態が悪い物ばかりでとても使える様な物を手に入れれたらラッキーだと思います。

    基本はトラスロッド限界で大きく順反り・トップ浮きも酷く弦高も高い物が多いので、まず使用できるレベルじゃない物が多いです。

    そうした意味でも使用できる状態というのは価値があります。
    昔の低価格帯は数万円でも現在の20~30万円と同じ位と言っても良い位の物が多いです。

    ありがとうございました♪


    This is a Yamaha FG-180 fret grind and nut groove cut adjustment.

    It is an old model, but the frets had been replaced in the past, and the condition seemed to have improved.

    We were able to finish the guitar by matching the frets and cutting the high nut to make it easier to play.

    The Yamaha FG series has a lot of good sound quality at a low price point, but the ones you can find used in recent years are all in poor condition, so you would be lucky to get a very usable one.

    The basic condition of the FG series is at the limit of the truss rod, and most of them are not usable because of the large forward warp, top lift, and high string height.

    In this sense, it is valuable to have them in usable condition.
    In the old days, many of the low-priced ones were priced at several tens of thousands of yen, which is about the same as today’s 200,000-300,000 yen.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231104193123
  • FenderUSA 60年代テレキャスター セットアップ

  • 2024/05/14
  • Category:
  • フェンダーUSA製60年代製テレキャスターのセットアップです。

    68年製、ブリッジが変わっててオクターブが合ってない状態です。

    やや順反りを調整しました。ヴィンテージの物にしては比較的状態が良いです。

    ヴィンテージ楽器を購入する際に注意点としては状態がまともに弾けるレベルなのか?を必ず確認して下さい。

    特に詳細も無く「良い物!価値がある!」として販売されていたりしますが、当然ながら古い物なので基本的には状態が悪い物が大半です。
    致命的な状態の物も多いので、この辺りをチェックした上で買わないと後から不具合を指摘しても「古い物だからしょうがない、何で分かってて買っていないんだ?」と扱われる事になります。
    ヴィンテージ楽器を購入するには目利きできる知識が無いと難しいかもしれません。

    ありがとうございました♪


    This is a Fender USA 60’s Telecaster setup.

    Made in ’68, bridge has been changed and octave is not correct.

    I have adjusted the slightly forward warp. It is in relatively good condition for a vintage item.

    Please be careful when you buy a vintage instrument, and be sure to check if the condition is decent enough to play. Please make sure to check if it is in decent playable condition.

    If there are no details and you think “It’s a good one! Worth it! but most of them are in poor condition because they are old.
    If you don’t check the condition of the item before you buy it, you will be treated as if the item is old and you don’t know why you didn’t buy it when you point out the problem later. If you point out the defect later, you will be treated as “It’s just an old instrument, why didn’t you buy it knowingly?
    It may be difficult to buy a vintage instrument if you don’t have a good eye for vintage instruments.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20231202215934
  • FenderJAPAN Eシリアル ストラトキャスター PU交換&セットアップ VANZANDT VINTAGE PLUS

  • 2024/05/13
  • Category:
  • IMG20231202210316

    フェンダージャパン製ストラトキャスター、EシリアルのPU交換・セットアップです。

    フロントのみヴァンザント製ヴィンテージプラスに交換です。自分も好きなPUですね。

    ヴァンザント製PUは特にシングルPUが優秀で、価格も他と比べて安いのでシングルコイルPUの交換なら選択肢としてはまずこれらが入ってくる事と思います。

    音の粘りや太さが丁度良いバランスです。
    ヴァンザント製もヴィンテージプラスやトゥルーヴィンテージが売れ線と思いますが、近年は他メーカー品が品薄になっている背景からこうしたパーツも買える内に購入していた方が良いかもしれません。

    ありがとうございました♪


    This is a PU replacement and setup for a Fender Japan Stratocaster, E serial.

    Only front PU is replaced with Van Zandt Vintage Plus. I like this PU.

    Van Zandt’s PUs are excellent, especially single PUs, and their price is lower than other PUs.

    The sound has just the right balance of stickiness and fatness.
    Vintage Plus and True Vintage are the best sellers in the Van Zandt line, but with the recent shortage of other makers’ products, it would be better to buy these parts while you can.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE