タグ別アーカイブ: Gibson

    IMG20241031192746
  • Gibson エクスプローラー PU交換&セットアップ SEYMOUR DUNCAN SH-4

  • 2025/04/06
  • Category:
  • ギブソン製エクスプローラーのPU交換・セットアップです。

    リアをセイモアダンカン製SH-4に交換しました。

    定番のリアPUとなりますが歪ませた時の音が好む人が多い様で昔からの売れ筋商品の様子です。
    SH-4も販売がかなり古いので、そうした意味では歴史が古いPUとなるので現代のPUの方がより粒が細かく綺麗に歪みますがこの荒さが良いのかもしれません。

    ありがとうございました♪


    This is a Gibson Explorer PU replacement and setup.

    The rear PU has been replaced with a Seymour Duncan SH-4.

    This is a standard rear PU, but many people seem to like the sound when distorted, and it has been a hot seller for a long time.
    The SH-4 has been on the market for quite a long time, so in this sense, it is an old PU, and modern PUs distort more finely and beautifully, but this roughness may be good.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250110_113632291
  • Gibson CustomShop ES-355 セットアップ

  • 2025/03/25
  • Category:
  • ギブソンカスタムショップ製ES-335のセットアップです。

    比較的に状態が良い良質個体で音も良い個体です。

    全体的に電装のガリは出ているが使えるレベルではあります。
    箱物は電装パーツに汚れが入り易いので消耗とは別にガリが出易いので中古品は基本的に交換が推奨です。

    調整する事で弾き易い状態に仕上げる事ができました。

    ありがとうございました♪


    This is a Gibson Custom Shop ES-335 setup.

    This is a good quality unit in relatively good condition and sound.

    The overall condition is usable, although there is some electrical rattling.
    The boxed model is easy to get dirt in the electrical parts, so it is easy to get gurgling apart from wear and tear.

    We were able to make it easy to play by adjusting it.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241213175748
  • Gibson Non-Reverse Thunderbird サンダーバード ペグ位置修正&ナット交換

  • 2025/03/13
  • Category:
  • ギブソン製ノンリバースサンダーバードのペグ位置修正・ナット交換です。

    ヒップショットペグに交換されているが、ピッチが狭く回すと隣のペグに当たるので位置をズラして取り付け加工しました。

    ナット溝が死んでいる為、音が詰まるので交換しました。

    音が良く太く鳴りが良いです。
    ギブソン製はギターよりもベースが良く、自然な低音が無加工で出てくるので難しい音作りをしなくてもアンプはフラットで良い音が出せる良質メーカーです。
    不思議とベースが評価されないのが謎な所です。ギブソンはギターよりもベースメーカーです。

    ありがとうございました♪


    This is a peg position correction and nut replacement for a Gibson non-reverse Thunderbird.

    It has been replaced with a hip shot peg, but the pitch is too narrow and when turned, it hits the adjacent peg, so we shifted the position and processed the installation.

    The nut groove is dead and the sound is clogged, so we replaced it.

    The sound is good, fat and ringing.
    Gibson is a quality maker that produces better basses than guitars, and the amp can produce a flat and good sound without difficult sound production because the natural bass comes out without any processing.
    Strangely enough, the bass is the mysterious part that is not appreciated. Gibson is more a bass maker than a guitar maker.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241113220058
  • メーカー不明 レスポール PU交換&セットアップ Gibson “Dirty Fingers”

  • 2025/03/02
  • Category:
  • IMG20241113205931

    メーカー不明の何かしら国産モデルをモデファイした様なレスポールのPU交換・セットアップです。
    ロゴが無いのでメーカー不明です。

    PUを持ち込みのギブソン製ダーティフィンガーに交換です。
    古い年代のパワーがあるモデルですね。

    音がタイトで荒い歪みなサウンドになりました。
    ダーティフィンガーは70年代に登場したとの事ですが歴史が古い事から音も現代のハイパワー系PUとは音のニュアンスが異なります。
    こうしたモデルを弾いてみると現代に行くにつれ歪みが細かく綺麗に聞こえてきます。
    そうした意味ではダーティフィンガーは近年には出せない歪みサウンドが出せます。

    ありがとうございました♪


    This is a PU replacement/setup for a Les Paul that looks like a modification of some domestic model from an unknown maker.
    The maker is unknown because there is no logo.

    The PU is replaced with a Gibson Dirty Finger.
    This model has a lot of power in the old age.

    The sound is now tight and rough distorted.
    Dirty Finger was introduced in the 70’s. Because of its old history, the sound is different from modern high-power PUs.
    When you play these models, you can hear the distortion more finely and beautifully as you go up to the modern era.
    In this sense, Dirty Finger can produce a distortion sound that cannot be produced in recent years.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241113204647
  • Gibson レスポール ナット高調整&セットアップ

  • 2025/02/27
  • Category:
  • ギブソン製レスポールのナット高調整・セットアップです。

    中古品の購入との事ですが弦高が高い状態で弾き難いです。

    ナットが素人作業で触られている様子で溝幅が妙に広く、溝も接着剤で埋められている様子。
    その理由もあってナット高が高い状態です。

    溝切りを行い調整する事で弾き易くなりましたが素人が手を加えているとこの状態で完璧とも言い難く、心配であればナット自体を交換した方が良いです。
    素人が作業した物は基本的に信用ができませんので、手が加わった物は基本的に新品交換する事をお勧めします。

    ありがとうございました♪


    This is a Gibson Les Paul nut height adjustment and setup.

    The guitar was purchased used, but it is hard to play because of the high string height.

    The nut seems to have been touched up by an amateur, and the groove width is strangely wide, and the groove seems to have been filled with glue.
    This is one of the reasons why the nut height is so high.

    However, it is difficult to say that the nut is perfect if it has been touched by an amateur.
    If you are worried about it, it is better to replace the nut itself.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240723214456
  • Gibson レスポール 90年代 フレットすり合わせ&ナット交換

  • 2025/02/24
  • Category:
  • ギブソン製レスポールのフレットすり合わせ・ナット交換です。

    ネックにヒビが入っておりますがチューニングしても開かず問題無い程度で、これを直すには中途半端な状態ですのでこのまま使用する事となりました。

    ナットが消耗で音が詰まり気味・音が詰まるフレット箇所がある状態です。

    ナット交換・フレットすり合わせを行う事で問題無い状態に仕上げる事ができました。

    かなり音が良い個体です。90年代前半は良い個体が多いので下手なヴィンテージで音も状態も良くない物を買うより90年代が狙い目です。

    ありがとうございました♪


    This is a Gibson Les Paul with fret adjustment and nut replacement.

    There is a crack in the neck, but it does not open when tuned and is not a problem.

    The nut is worn out, and there are fretted areas where the sound is stuck or clogged up.

    By replacing the nut and adjusting the frets, we were able to finish it up without any problems.

    There are many good vintage guitars in the early 90’s, so it is better to buy a vintage guitar in the 90’s than a bad vintage one that is not in good sound and condition.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241105175703
  • Gibson レスポール ネック折れリペア

  • 2025/02/03
  • Category:
  • IMG20241104175010

    ギブソン製レスポールのネック折れリペアです。

    どうしても角度付きネックは折れ易いので気を付けて使用する他、折れてしまったら割れ口が変形する前に直す事が重要です。
    割れ方さえ問題無ければ基本は接着で直す事が可能です。

    接着後は問題無く弾ける状態に修正ができました。

    音は出るがトグルスイッチの動きがおかしいので、不具合が出てくる様ならトグルスイッチは交換が必要です。

    ありがとうございました♪


    This is a neck break repair for a Gibson Les Paul.

    Angled necks are prone to breakage, so it is important to use them with care and, if they break, to repair them before the cracks become deformed.
    As long as the breakage is OK, it can basically be repaired by gluing.

    After gluing, the neck can be played without any problem.

    The toggle switch is not working properly, so if the problem persists, the toggle switch will need to be replaced.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241103192254
  • Gibson EB-2 配線直し&ネック折れリペア

  • 2025/01/30
  • Category:
  • IMG20241102200027

    ギブソン製EB-2の配線直し・ネック折れリペアです。

    音が出なくなる時があるとの事で交換と修正を行いました。

    ネック折れしてるが普通にチューニングし弾けるレベルの割れでした。
    ネック折れは折れ方次第で作業可能か不可か、接着のみで直るのか様々ですが折れたら早く直す事が共通です。
    割れ箇所が変形してしまうと接着が困難になっていきます。

    オクターブビスが固着している・4弦側の取付位置が大きくズレている(4弦側オクターブがかなり低い)状態です。
    ギブソンの製造精度が出ている様な個体ですね。
    サドルが単体で動かせるモデルでも大きくズレて付いている事も現行品であり、高額なモデルでもそうした個体があったりしますので要注意です。
    チューンOマチックの取付位置がズレているとオクターブが合わない不具合が出てきます。そうした個体は楽器ではないので返品案件です。

    接着後は問題無い状態になり音も安定して出せる状態になりました。
    オクターブが大きく狂ってはいるのですが、この辺りはヴィンテージ精度でもあるので大掛かりなリペアを行うのも考え物です。
    ブリッジの位置修正は元の穴を埋めて新たな位置に空け直す事となりますが、その埋めた箇所が見える状態になります。
    ヴィンテージ楽器自体の価値を下げる事にもなるので、ヴィンテージ楽器は基本的に状態が悪く現代に使用する道具としては難しい個体も多いので嗜好品です。

    ありがとうございました♪


    This is a Gibson EB-2 rewiring and neck break repair.

    Replaced and fixed the problem with the sound sometimes going out of tune.

    The neck was broken, but the crack was at a level where the guitar can be tuned and played normally.
    Depending on how the neck is broken, it may or may not be repairable, or it may be repairable only by gluing it back together.
    If the crack is deformed, it will be difficult to glue it back together.

    The octave screws are sticking, and the mounting position of the 4th string side is greatly misaligned (the octave of the 4th string side is very low).
    This is an example of Gibson’s manufacturing precision.
    Even if the saddle can be moved independently, it is possible for the current model to have a large misalignment, and even some of the more expensive models have such a misalignment.
    If the tuning-o-matic is not in the correct position, the octave may not match. Such pieces are not musical instruments and should be returned.

    After gluing, there is no problem and the sound is now stable.
    Although the octave is not quite correct, it is not a good idea to do a major repair because of the vintage accuracy of this area.
    To correct the position of the bridge, we have to fill the original hole and re-position it, but the filled hole will be visible.
    Vintage instruments are basically in poor condition and are difficult to use as a tool in modern times, so they are a luxury item.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240822203349
  • Gibson CustomShop レスポール フレットすり合わせ

  • 2025/01/17
  • Category:
  • IMG20240821192923

    ギブソンカスタムショップ製レスポールのフレットすり合わせです。

    ぶつけたのかフレットに弦の跡があり引っ掛かる状態です。

    全体消耗も含めすり合わせで対処しました。

    中古品等にも多いですが弾く上で難点がある部分はナット・フレットに多く見られます。
    これらは自然に良くなる事はありませんのでリペア必須になる箇所になります。

    中古品も販売側が素人レベルな所も多いので難点を隠して売ってたり、難点かどうかすらも分からないまま売っている事も多いので気を付けましょう。

    ありがとうございました♪


    This is a Gibson Custom Shop Les Paul fret grinder.

    There are string marks on the frets from bumping and catching.

    We have done this by fret fret adjustment including overall wear and tear.

    The nut and frets are the most common areas that are difficult to play, as is often the case with second-hand Les Paul.
    These will not naturally get better, so repair will be necessary.

    Since there are many used instruments that are sold at the amateur level, there are many cases where the seller hides the difficult parts or sells them without even knowing if they are difficult or not, so be careful.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240905191650
  • Gibson ファイヤーバード PU交換&セットアップ Seymour Duncan CustomShop

  • 2025/01/15
  • Category:
  • IMG20240905181014

    ギブソン製ファイヤーバードのPU交換・セットアップです。

    お客様持ち込みのダンカンカスタムショップPUに交換しました。
    ミニハムは選択肢が少ないので限られた物で交換する他ありません。

    音が柔らかく扱い易いサウンド、テレキャスターを良くした様なサウンド傾向です。
    キャラクターが大きく変化した様な印象です。ミニハムはどうしても癖強なサウンド傾向かと思いますがその辺りが緩和され扱い易くなったので使用できる音が増えた印象です。

    ありがとうございました♪


    This is a Gibson Firebird PU replacement and setup.

    We replaced it with a Duncan Custom Shop PU brought in by the customer.
    There are only a few choices of mini hums, so we had to replace it with a limited number of them.

    The sound is soft and easy to handle.
    I have the impression that the character has changed a lot. I think the mini-ham has a tendency to sound habitual, but now it is easier to handle, so I have the impression that the number of usable sounds has increased.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE