カテゴリー別アーカイブ: リペア

    PXL_20250709_085851592
  • Gretsch G6134TG FSR Penguin with String-Thru Bigsby -Black- セットアップ

  • 2025/10/17
  • Category:
  • グレッチ製6134のセットアップです。

    ネックにヒビが入っており、こちらはチューニングしてみると割れがほんの僅かしか開かず接着作業が難しい状態ですのでネック折れ修理は保留となりました。

    ネック折れ修理は判断が難しく、こうした演奏として使えはするけど亀裂やヒビがある程度であれば問題無く使用しても良いと判断もできます。

    狭い隙間の割れを広げて接着作業してしまうにしても二次災害(開いた割れが複雑に折れる等)も考えられるリスクもあるので、現状で問題無いなら触らない方が良いと判断します。

    またチューニングが狂い易い理由としてナット溝がキツイ状態です。

    また音が良いモデルでした。

    ありがとうございました♪


    Setup for a Gretsch 6134.

    The neck has a crack. When tuning, the crack only opens slightly, making adhesive repair difficult. Therefore, neck break repair has been postponed.

    Neck break repair is a difficult judgment call. If the instrument is playable despite cracks or splits, it may be deemed acceptable for continued use.

    Even if we were to widen the narrow gap and attempt gluing, there’s a risk of secondary damage (like the opened crack fracturing in complex ways). Therefore, if it’s currently playable without issues, we judge it best to leave it as is.

    Additionally, the nut grooves are too tight, which is why it goes out of tune easily.

    It was also a model with a great sound.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250706_113241755
  • FenderUSA ジャズマスター 左利き セットアップ

  • 2025/10/14
  • Category:
  • フェンダーUSA製ジャズマスターのセットアップです。

    左利きモデルになります。

    新品購入したモデルですが特に状態に不具合無しで調整できました。

    左利きモデルは数が少なく、選択肢も非常に限られてくるので大変かもしれません。

    左利きモデルのボディさえあれば通常の右利きネックを付けて弾く事もできるのですが、中古でも多くは出回らないと思うので左利きの方は購入時に苦労するのでメーカーもこの辺りはもう少し増産しても良いと思います。

    ありがとうございました♪


    This is a setup for a Fender USA Jazzmaster.

    It is a left-handed model.

    Although it was purchased new, it was in perfect condition and required no adjustments.

    Left-handed models are scarce, and the selection is extremely limited, so it can be quite challenging.

    If you have a left-handed body, you could theoretically attach a standard right-handed neck and play it. However, even used ones don’t seem to circulate much, so left-handed players often struggle to find one. Manufacturers could really increase production in this area.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250614_120207394
  • Bizen Works Grain Arched ポット交換&ジャック交換&セットアップ

  • 2025/10/13
  • Category:
  • ビゼン製レスポールのポット交換・ジャック交換・セットアップです。

    リアボリューム・ジャックにガリで新品に交換しました。

    ジャックは消耗するパーツNo.1ですので定番の修理ですが、ポットやセレクターは多様する程に消耗するのでガリが出たタイミングで交換がベストです。

    実際に新品パーツに交換すると音質も良くなるので、消耗=音も悪くなっています。

    消耗の劣化は接点洗浄剤で直しても無駄なので、電装パーツは消耗品と割り切って交換しながら使用していきましょう。

    ありがとうございました♪


    Potentiometer replacement, jack replacement, and setup for a Bizen-made Les Paul.

    Replaced the rear volume and jack with new ones due to crackling.

    The jack is the number one wear part, so this is a standard repair. However, potentiometers and selectors wear out with use, so replacing them when crackling occurs is best.

    Replacing them with new parts actually improves the sound quality, proving that wear equals sound degradation.

    Attempting to fix deterioration with contact cleaner is futile. Accept that electrical components are consumables and replace them as needed while using the guitar.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250805_100634854
  • moon テレキャスター ジャック交換

  • 2025/10/12
  • Category:
  • ムーン製テレキャスターのジャック交換です。

    音が使用してて途切れる事があるとの事で各所の電装パーツをチェックした所、ジャックがダメそうです。

    ジャックが原因の様子でしたので新品に交換しました。

    電装パーツは基本的に使用が長い場合は全交換がお勧めです。

    電装パーツは消耗品ですので、トラブルが起きない様にコントロールをよく操作する様子であれば数年に1度は交換したい所です。

    厄介なのは「音が出る時と出ない時がある」で、チェック時に問題無い場合でも持ち帰った後で音が出なくなったりする事もあります。

    電装パーツは消耗すると不安要素となってきますので、大事なライブやレコーディングがあるギターは交換して使用していきたい所です。

    ありがとうございました♪


    Replacing the jack on a Moon Telecaster.

    The customer reported intermittent sound dropouts during use. After checking all electrical components, the jack appeared to be the culprit.

    Since the jack seemed to be the cause, we replaced it with a new one.

    For electrical components, we generally recommend replacing them entirely if they’ve been in use for a long time.

    Electrical components are consumables, so if you frequently use the controls, it’s best to replace them every few years to prevent issues.

    The tricky part is when the sound comes and goes. Even if everything checks out during inspection, the sound might stop working after the customer takes it home.

    Worn electrical components become a source of uncertainty, so for guitars used in important gigs or recordings, it’s wise to replace them before use.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250717_095038963
  • Thorn Tree ストラトキャスター フレット部分すり合わせ&セットアップ

  • 2025/10/10
  • Category:
  • ソーンツリー製ストラトキャスターのフレット部分すり合わせ・セットアップです。

    ネックがソーンツリー製造・ボディはフェンダージャパン製らしいとの事です。
    中古購入との事です。

    フレット状態が悪く音詰まり箇所があり、フレット自体の消耗は全体的にありませんが詰まる箇所があります。

    音詰まりしている箇所を部分的にすり合わせ、明らかダメな箇所は改善され全体的に弾けはする状態になりましたが可能であれば全体すり合わせした方が良い状態です。
    全体的にフレット状態が悪いです。

    またローフレット側の指板が膨張しており、ネックと指板の接着面の段差が目立つ状態です。
    こうした状態はネックアイロンを行った際に起き易いです。
    恐らく前オーナーがネックアイロンで直してみようとして状態が悪化し、手放した物と思われます。

    ネックアイロンで反り等が直る思ってる人は間違いで、まず問題無く直ったらラッキーです。
    熱を与える事による不具合も同時に発生するのでリスキーなリペア方法となります。
    恐らくネックアイロンを使用しないとダメな状態(トラスロッド限界でネック順反り等)をアイロンを使って直してみたら指板が熱で膨張し、膨張が元に戻らず指板とネックとの段差が手に当たって弾いてて違和感が出る状態になり、アイロン熱による指板の乾燥や膨張でフレットが抜ける等の動く様な状況になりフレット状態が全体的に悪くなってまともに弾く事ができなくなり前オーナーが手放したと思います。

    音は良さげなので、まともに使っていこうと思った際はすり合わせして使用する事をお勧めします。
    ありがとうございました♪


    Fret leveling and setup for a Thorn Tree Stratocaster.

    The neck appears to be manufactured by Thorn Tree, while the body is likely made by Fender Japan.
    It was purchased secondhand.

    The frets are in poor condition with some buzzing spots. While overall fret wear is minimal, there are specific areas causing buzz.

    We partially refretted the buzzing sections. Clearly problematic areas improved, and the guitar is now playable overall. However, a full refret would be preferable if possible.
    The overall fret condition is poor.

    Additionally, the fingerboard near the lower frets has swollen, creating a noticeable gap at the joint between the neck and fingerboard.
    This condition often occurs after attempting neck ironing.
    It’s likely the previous owner tried fixing it with neck ironing, worsened the condition, and then sold it.

    People who think neck ironing can fix warping are mistaken; getting it fixed without issues is pure luck.
    It’s a risky repair method because applying heat often causes additional problems.
    It seems the previous owner tried using a neck iron on a neck that was likely already beyond repair (e.g., severe reverse bow where the truss rod was maxed out). The heat caused the fingerboard to expand, and this expansion didn’t reverse. The resulting gap between the fingerboard and neck became noticeable to the touch while playing, creating discomfort. The fretboard drying out and swelling from the iron’s heat can cause frets to loosen or shift, leading to overall poor fret condition. This likely made it unplayable, prompting the previous owner to part with it.

    The sound seems promising, so if you plan to use it properly, I recommend refretting it.
    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250630_085445316
  • HISTORY Advanced セットアップ&コンデンサ交換

  • 2025/10/08
  • Category:
  • PXL_20250630_080426958

    ヒストリー製アドバンスドのセットアップ・コンデンサ交換です。

    一般的な楽器屋で売ってるコンデンサで、付いている物も10万円台にあったりします。

    交換後は音が柔らかくなる事とトーン0でもコモリ過ぎないので思ってたよりも良いコンデンサでした。

    コンデンサも音が変わるのは事実ですがギターの場合はビジネス目的でヴィンテージコンデンサ等が過度に扱われ過ぎているので要注意です。

    今回の様に安いコンデンサでも音は良かったりするので騙されない様に。

    ありがとうございました♪


    This is a capacitor replacement for a History Advanced setup.

    These are capacitors sold at regular music stores, and some models even come with ones priced in the 100,000 yen range.

    After replacement, the sound became softer, and even with the tone knob at zero, it didn’t get overly muffled. It turned out to be a better capacitor than I expected.

    While it’s true that capacitors can change the sound, be cautious with guitars—vintage capacitors and such are often overhyped for commercial purposes.

    As seen here, even inexpensive capacitors can sound great, so don’t be fooled.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250502_082816250
  • Ibanez RG フレットすり合わせ&配線直し

  • 2025/10/07
  • Category:
  • アイバニーズ製RGのフレットすり合わせ・配線直しです。

    センターPUが壊れており音が出ない状態です。
    フレットも消耗が全体的に大きい状態です。

    お客様との相談で電装を全て交換・3Wayセレクター仕様にしてフロントとリアで鳴る仕様となりました。

    フレットをすり合わせする事で演奏も良い状態で弾ける事となりました。

    モダン系サウンドかと思いましたが音が柔らかく、クリーンでも良いサウンドが出せる個体です。
    昔は日本製アイバニーズも低価格帯で良い個体が大量生産されていただけに中古品でもお勧めできる個体です。
    ただ補強材も入っていない薄いネックは状態が悪い事も多いので購入時は注意したいポイントです。

    ありがとうございました♪


    Ibanez RG fret leveling and rewiring.

    The center pickup is broken and not producing sound.
    The frets show significant overall wear.

    After consulting with the customer, we replaced all electronics and converted it to a 3-way selector configuration, enabling sound from both the front and rear pickups.

    Fret leveling has restored the guitar to a playable condition.

    While expected to have a modern sound, it actually produces a soft tone and delivers excellent clean tones.
    Given that Japanese-made Ibanez guitars were once mass-produced at affordable prices with good quality, this used model is highly recommended.
    However, the thin neck without reinforcement often deteriorates quickly, so this is a key point to check when purchasing.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250729_085153127
  • フジゲン プレシジョンベース セットアップ 左利き

  • 2025/10/06
  • Category:
  • フジゲン製プレシジョンベースのセットアップです。

    左利きモデルになります。

    新品アウトレット品で安くなっていたモデルとの事ですが最初からトラスロッドの余り量が少ない状態です。

    調整でトラスロッドが殆ど限界状態になりました。

    近年はこうした新品でもトラスロッドの余り量が少ない事が非常に多くなりましたので、長持ちする個体を買う意味でもトラスロッドの余り量が多い物を買わないと損します。
    具体的に購入前にトラスロッドを店員にお願いして目の前で回してもらい、余り量を確認してから購入した方が良いです。

    ありがとうございました♪


    This is the setup for a Fujigen Precision Bass.

    It is a left-handed model.

    It was a new outlet model sold at a discount, but it had very little truss rod adjustment range from the start.

    Adjusting it brought the truss rod almost to its limit.

    In recent years, it has become very common for even new instruments to have insufficient truss rod adjustment range. To ensure you get a long-lasting instrument, it’s essential to purchase one with ample truss rod adjustment range.
    Specifically, before buying, ask the salesperson to turn the truss rod in front of you to check the remaining adjustment range before making your purchase.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250520_111041551
  • Sago オーダーギター ブリッジ修正&セットアップ

  • 2025/10/05
  • Category:
  • サゴ製オーダーギターのブリッジ修正・セットアップです。

    1~3弦が切れ易いとの事で持ち込まれました。

    サドルの消耗?なのかブリッジサドル上で弦の痕が大きく付いており、これが弦が切れる原因の様子です。

    近年はパーツの品質も低下している様で(昔は弦が切れ易い話をあまり聞いてない)、弦が当たる所が鋭角だったりすると切れ易くなります。

    サドル溝を削って磨いて修正しました。

    音のレンジが広く、タイトでクリアーなサウンドです。

    指板にリグナムバイタが使用されており珍しい仕様です。硬い材でもあるのでネック強度も高くする事が可能です。

    ありがとうございました♪


    Bridge repair and setup for a custom-made Sago guitar.

    Brought in because strings 1 through 3 were breaking easily.

    Significant string marks were found on the bridge saddle, possibly due to saddle wear? This appears to be the cause of the string breaks.

    Part quality seems to have declined in recent years (we rarely heard about strings breaking easily in the past), and sharp angles where the strings contact the bridge can make them break more readily.

    We corrected this by shaving and polishing the saddle grooves.

    The result is a wide tonal range with a tight, clear sound.

    The fretboard uses Lignum Vitae, a rare specification. Being a hard wood, it also allows for increased neck strength.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250607_092400214
  • LAKLAND SL44-94 Deluxe ジャック交換&セットアップ

  • 2025/10/03
  • Category:
  • レイクランド製SL44-94のジャック交換・セットアップです。

    トラスロッドに殆ど余裕が無い状態です。音が途切れる事からジャックが消耗している状態です。

    ジャック交換し音が安定して出る状態になりました。

    トラスロッドの余り量は残り少ないですが音が良く弾き易い状態に仕上げる事ができました。

    ありがとうございました♪


    Replacement and setup of the jack on a Lakeland SL44-94.

    The truss rod had almost no adjustment range left. The sound was cutting out, indicating the jack was worn out.

    After replacing the jack, the sound is now stable.

    While the truss rod adjustment range remains limited, we’ve achieved a state where the sound is good and the guitar is easy to play.

    Thank you very much!


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE