カテゴリー別アーカイブ: リペア

    senad-palic-3bgcqIiFdRk-unsplash
  • 「あれ?なんかおかしい…」初心者が状態の悪いギターを買ってしまった時の対処法

  • 2025/06/30
  • Category:

  • もしかして、ハズレを引いちゃった…?

    せっかく手に入れた憧れのギター。いざ弾いてみようと思ったら「なんか音が変…」「弾きにくい…」「これって不良品?」と感じたことはありませんか?

    特にギター初心者の場合、何が正常で何が異常なのか判断が難しいもの。もしかしたら、状態の悪い楽器を購入してしまったのかもしれません。

    そんな時、「やっぱり自分には向いてないんだ…」と諦めてしまうのは、あまりにももったいない!実は、適切な対処をすれば、そのギターが快適に弾けるようになる可能性は十分にあります。

    この記事では、もしあなたが「状態の悪いギターを買ってしまったかも?」と感じた時に、冷静に、そして前向きに対処するための具体的な方法を解説します。

    emily-finch-aW2ELKtnbRU-unsplash

    ~「もしかして?」と感じる状態とその原因~

    まずは、どんな症状があったら「状態が悪いかも」と疑うべきか、具体的な例を見ていきましょう。

    ●パターン1:チューニングがすぐに狂う、音が合わない

    せっかく音を合わせたのに、数分でチューニングが狂ってしまう。
    特定のフレットを押さえると、他の弦も共鳴しておかしな音が出る。
    開放弦(どこも押さえない状態)と、同じ音程のフレットを押さえた音がズレている。

    ~考えられる原因~

    ・弦の劣化: 最も多い原因。古い弦はチューニングが安定しません。
    ・ペグの不具合: 弦を巻き上げるパーツ(ペグ)が緩い、あるいは摩耗している。
    ・ネックの反り: ギターのネックが正しい状態ではないため、弦の張りが不均一になっている。
    ・ナットやブリッジの調整不足: 弦が乗っているパーツ(ナットやブリッジ)の溝が適切でない。

    ●パターン2:弦を押さえにくい、指が痛すぎる

    力を入れても弦が押さえられない。
    他の人のギターよりも明らかに弦が固く感じる。
    弦とフレットの間の隙間(弦高)が異常に高い。

    ~考えられる原因~

    ・弦高が高すぎる: これが最も一般的。適切な高さに調整することで劇的に弾きやすくなります。
    ・弦の太さ: 初心者には細い弦の方が弾きやすいです。
    ・ネックの反り: ネックが順反りしていると弦高が高くなります。

    ●パターン3:ビビり音が出る、音が出ない

    弦を押さえて音を出すと、「ジージー」「ビーン」といった不快なビビり音が出る。
    特定のフレットを押さえると、全く音が出ない箇所がある。

    ~考えられる原因~

    ・弦高が低すぎる: 弦がフレットに触れてしまっている。
    ・ネックの反り: ネックが逆反りしているとビビり音が出やすくなります。
    ・フレットの摩耗や浮き: フレットが不均一になっている。
    ・電装系のトラブル(エレキギターの場合):ジャックの接触不良、配線の断線など。

    emma-ou-O6L9m7Tm1VY-unsplash

    ~「ハズレ」を引いてしまった時の対処法5ステップ~

    症状に心当たりがあったら、以下のステップで冷静に対処していきましょう。

    ・ステップ1:まずは落ち着いて「弦を交換」してみる
    意外と見落としがちなのが、弦の劣化です。古い弦はチューニングが安定しないだけでなく、錆びていれば押さえにくさやビビりの原因にもなります。

    まずは、新しい弦に交換してみてください。驚くほど改善されるケースも少なくありません。弦交換はギターを弾く上で必須のスキルなので、この機会にぜひ覚えてしまいましょう。

    ・ステップ2:ギターに詳しい友人や知人に相談する
    もし身近にギター経験者がいれば、迷わず相談してみましょう。

    「このギター、なんかおかしいんだけど、見てくれない?」と頼んでみてください。彼らはあなたのギターの状態を見て、何が問題なのか、そしてどうすれば良いのか、的確なアドバイスをくれるはずです。素人判断では見落としがちな点も、すぐに気づいてくれるかもしれません。

    ・ステップ3:購入店に相談・修理を依頼する
    新品で購入した場合や、中古でも信頼できる楽器店で購入した場合は、購入店に相談するのが最も確実です。

    ・初期不良の可能性: 購入から日が浅い場合は、初期不良として無償で対応してくれる可能性があります。

    ・保証の確認: 保証期間内であれば、修理費用がかからない場合もあります。

    ・調整依頼: 「弾きにくいので、調整してもらえませんか?」と相談しましょう。多くの場合、有料にはなりますが、専門のスタッフがギターの状態を最適に調整してくれます。これを**「セットアップ」**と呼びます。

    ●ステップ4:信頼できるリペアショップに持ち込む

    もし購入店での対応が難しい場合や、中古品で保証がない場合は、専門のリペアショップに持ち込みましょう。

    リペアショップは、ギターの修理や調整を専門に行うお店です。プロの目でギターの状態を診断し、適切な修理や調整を行ってくれます。

    「どこかおかしいのですが、見ていただけますか?」と相談すれば、見積もりを出してくれます。費用はかかりますが、あなたのギターを快適な状態に蘇らせてくれるはずです。リペアショップは、ギターを長く愛用していく上で、心強い味方になってくれますよ。

    ●ステップ5:もしもの時は「買い替え」も視野に入れる

    ここまで試しても改善が見られない、あるいは修理費用がギター本体の価格を大幅に上回ってしまうような場合は、新しいギターへの買い替えも選択肢の一つとして考えてみましょう。

    今回の経験を教訓に、前回の記事で紹介した「買って後悔しないためのギター選びの鉄則」を参考に、今度は「本当に良い一本」を見つけるチャンスです。

    ~まとめ~

    諦めないで!あなたのギターはきっと良くなる!

    せっかく手に入れたギターが「ハズレ」だったかも…と落ち込む気持ちはよく分かります。しかし、そこで諦めてしまうのはもったいない!

    弦交換や専門家への相談で、あなたのギターは劇的に弾きやすくなる可能性があります。そして何より、そういったトラブルを乗り越えることで、あなたはギターについてより深く知り、愛着も一層深まるはずです。

    もし今、あなたのギターに不調を感じていたら、ぜひこの記事を参考に、次のステップを踏み出してみてください。あなたのギターライフが、より豊かになることを願っています!

    読んで頂きありがとうございました!


    Maybe I got the wrong guitar…?

    You’ve taken the trouble to get a guitar that you’ve always dreamed of. But when you try to play it, have you ever thought, “Something sounds strange…”, “It’s hard to play…”, “Is this a defective guitar? Have you ever felt that the sound is strange…?

    Especially for guitar beginners, it is difficult to judge what is normal and what is abnormal. Perhaps you have purchased an instrument that is in poor condition.

    In such a case, it would be too much of a waste to just give up and say, “It’s not for me after all…” In fact, if you take the appropriate measures, you will be able to play it just fine! In fact, there is a good chance that you will be able to play that guitar comfortably if you take the appropriate measures.

    In this article, we will discuss how you can take care of your guitar if you feel “I might have bought a guitar in a bad condition…” I will explain concrete methods to deal with the situation calmly and positively.

    ~What are the conditions and causes of the “maybe?” and the cause of the condition

    First, let’s look at some specific examples of symptoms that should make you suspect that the condition may be bad.

    Pattern 1: Tuning goes out of tune quickly and the notes do not match.

    After you have gone to the trouble of tuning the instrument, the tuning goes out of tune within a few minutes.
    When you press down on a particular fret, other strings resonate and produce a strange sound.
    The sound of an open string (no strings pressed) and the sound of a fret pressed at the same pitch are out of tune.

    ~Possible causes

    Deteriorated strings: This is the most common cause. Old strings are not stable in tuning.
    Peg failure: The string winding parts (pegs) are loose or worn out.
    Warped neck: The neck of the guitar is not in proper condition, resulting in uneven string tension.
    Insufficient adjustment of the nut or bridge: The grooves in the parts on which the strings ride (nut or bridge) are not properly grooved.

    Pattern 2: Hard to hold the strings, too much finger pain.

    The strings cannot be held down even if you put a lot of effort into it.
    The strings feel noticeably harder than other people’s guitars.
    The gap between the strings and frets (string height) is abnormally high.

    ~Possible causes

    String height is too high: This is the most common cause. Adjusting the strings to an appropriate height will dramatically improve playing comfort.
    Thin strings are easier for beginners to play.
    Neck warp: If the neck is bowed forward, the string height will be higher.

    Pattern 3: Chattering sound or no sound

    When pressing the strings to produce a sound, an unpleasant buzzing sound such as “jeezy” or “beep” is produced.
    When pressing a specific fret, there is no sound at all.

    ~Possible causes

    String height is too low: The strings are touching the frets.
    Neck warp: If the neck is warped, it is easy for a chattering sound to be produced.
    Worn or uneven frets: The frets are uneven.
    Electrical problems (in the case of electric guitars): Poor contact with jacks, disconnection of wires, etc.

    ~The following are 5 steps to take when you have pulled a “Hazure” guitar.

    If you recognize any of the symptoms, follow the steps below to calmly deal with the problem.

    Step 1: First, calmly “replace the strings.
    What is often overlooked is the deterioration of the strings. Old strings are not only unstable in tuning, but if they are rusty, they can also cause difficulty in holding down the strings and chattering.

    First, try replacing them with new strings. In many cases, you will be surprised at the improvement. Changing strings is an essential skill for guitar players, so take this opportunity to learn how to do it.

    Step 2: Consult a friend or acquaintance who knows about guitars.
    If you know someone close to you who has experience with guitars, don’t hesitate to ask them for advice.

    If you have a friend or acquaintance who is familiar with guitars, don’t hesitate to ask them for advice: “There’s something wrong with this guitar. They can take a look at the condition of your guitar and see what’s wrong with it. They will be able to look at your guitar and give you accurate advice on what is wrong and what to do about it. They may also be able to immediately notice things that are often overlooked by amateurs.

    Step 3: Consult with the store of purchase and request repair.
    If you purchased the guitar new or used at a reputable music store, it is most reliable to consult with the store of purchase.

    If the instrument was purchased new, or if it was purchased used from a reputable music store, the best thing to do is to consult the store where you purchased the instrument.

    Check the warranty: If the instrument is under warranty, there may be no charge for repair.

    Request for adjustment: Ask the dealer, “I have a hard time playing, could you please adjust it? In most cases, there is a charge for this service, but you may be able to get a specialist to do it for you. In most cases, there is a charge for this service, but a professional will adjust the guitar to its optimum condition. This is called **”setup.

    Step 4: Take the guitar to a reliable repair store.

    If the store where you purchased the guitar is unable to help you, or if the guitar is used and has no warranty, take it to a professional repair store.

    Repair stores specialize in repairing and adjusting guitars. They will professionally diagnose the condition of your guitar and make appropriate repairs or adjustments.

    If you ask, “There is something wrong with my guitar, can you take a look at it? and they will give you an estimate. Although it will cost more, they will be able to bring your guitar back to a comfortable state. A repair store will be a reassuring ally in helping you keep your guitar for a long time.

    Step 5: If something goes wrong, consider “replacing” the guitar.

    If there is no improvement after trying all of the above, or if the repair cost is much more than the price of the guitar itself, consider replacing the guitar with a new one as one of your options.

    If you have learned from this experience and refer to the “Iron Rules for Choosing a Guitar to Avoid Regretful Buying” in the previous article, you now have a chance to find a “really good one”.

    ~ Summary~.

    Don’t give up! Your guitar will get better!

    I understand how it feels to feel depressed that the guitar you went through all that trouble to get may not be the right one for you. However, it would be a waste to give up there!

    Your guitar can become dramatically easier to play with a string change or consultation with a specialist. Above all, by overcoming such problems, you will learn more about your guitar and become even more attached to it.

    If you are currently experiencing any problems with your guitar, please refer to this article and take the next step. We hope your guitar life will be enriched!

    Thank you for reading!


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250225_092330291.MP
  • Tokai ES-335 ネック折れリペア

  • 2025/06/29
  • Category:
  • PXL_20250224_100828080

    トーカイ製ES-335のネック折れリペアです。

    折れるのは今回で2回目との事(1回目は別のお店で修理した過去)です。

    何度か折れてしまうと当然ながら直せる可能性が低くなってくるのですが、折れ方・折れてる箇所によりその判断は異なります。
    どちらにしても折れてしまった際は下手に自分で手を加えない事、すぐに直す事が重要です。

    特に問題無く接着のみで直す事ができました。

    ありがとうございました♪


    This is a broken neck repair for a Tokai ES-335.

    This is the second time it has been broken (the first time was repaired at another store).

    If it is broken several times, of course, the possibility of being able to fix it becomes low, but the decision depends on how it is broken and where it is broken.
    In either case, it is important not to do anything to the broken part by yourself and to fix it immediately.

    I was able to fix it with only gluing.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250308_082354925
  • Taylor 214ce セットアップ

  • 2025/06/26
  • Category:
  • テイラー製214CEのセットアップです。

    順反りして弦高が高い状態です。

    またネックのねじれにより弦高を低くする事は難しいが、それでも一般的なアコギと比べテイラー製品は初期状態で弦高が低めなので弾き易く調整はできました。

    アコギは太い弦を張るのでネックの順反り・ウネリが起き易いのとボディ側はハイ起きやトップ浮きが起こってくるので弦は緩めて保管しないとまず長持ちしません。

    メーカー自体も弦は張りっぱなしで良いと公表していますが、結局はネックが順反るなりトップが浮いて弦高が上がる等してこの様な状態になります。

    ありがとうございました♪


    This is a Taylor 214CE setup.

    The string height is high due to forward bowing.

    The neck is twisted, so it is difficult to lower the string height, but it is still easy to play because of the low string height of Taylor products compared to most acoustic guitars.

    The neck of an acoustic guitar is prone to warping and swelling due to the thick strings, and the body side is prone to highs and top lift, so the strings must be kept loose or they will not last long.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250227_085226271
  • Ibanez RGD Standard ナット溝切り調整&セットアップ

  • 2025/06/23
  • Category:
  • Ibanez製RGDスタンダードのナット溝切り調整・セットアップです。

    ダウンチューニング(ドロップG#)で調整する内容です。

    太い弦を張る場合はナット溝に弦が入りませんので溝切りが必須となります。

    使用する弦は68-13弦となります。

    溝切り後のセットアップ後は音抜けが良く無駄な音が出ないクリーンサウンドで音の形がダウンチューニングでもかなり見え易い状態になりました。
    大体のプレイヤーは弦が細いので、ダウンチューニングには可能な限り太い弦を使用しましょう。

    ありがとうございました♪


    This is a nut groove cut adjustment and setup for an Ibanez RGD Standard.

    This is an adjustment for down tuning (drop G#).

    When thick strings are used, it is necessary to cut the nut groove because the strings will not fit in the nut groove.

    The strings used are 68-13 strings.

    After the groove cutting, the sound is now clean with no wasted sound, and the shape of the sound is now quite visible even in down-tuning.
    Most players have thin strings, so use thicker strings for down tuning whenever possible.

    Thank you very much… ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250317_101026155
  • dragonfly Border666 ポット交換&セットアップ

  • 2025/06/19
  • Category:
  • ドラゴンフライ製ボーダー666のポット交換・セットアップです。

    ボリュームにガリがあり、こちらは新品に交換しました。

    よく接点洗浄剤等で直ったと思う方が多いですが、基本的に消耗で起きたガリは直せませんので交換が必要になります。
    ピックガードや裏パネルで蓋された部分のパーツは汚れが入りガリになる事はあまり無く、基本は使い過ぎによる消耗破損となるので交換しましょう。
    箱物等は汚れが入りガリになる事もあります。

    チューニングはドロップC#で調整する内容です。

    ドロップチューニングにすると張る弦の太さ等でネック反りも大きく変化するので調整が大きく変わります。
    レギュラーチューニングからドロップチューニング仕様にする際は注意しましょう。

    ありがとうございました♪


    This is a pot replacement and setup for a Dragonfly Border 666.

    The volume has a buzzing sound, and we replaced it with a new one.

    Many people often think that contact cleaner etc. can fix the problem, but basically, galling caused by wear and tear cannot be fixed, so it needs to be replaced.
    Parts covered by the pick guard or the back panel do not often become dirty and galled, and should be replaced because they are basically worn out and damaged due to overuse.
    Boxed instruments can become dirty and scuffed.

    The tuning should be adjusted to drop C#.

    The neck warp varies greatly depending on the thickness of the strings used when tuning to drop tuning, so the adjustment will vary greatly.
    Please be careful when changing from regular tuning to drop tuning.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250316_114719589
  • YAMAHA SB500 Super Bass セットアップ

  • 2025/06/16
  • Category:
  • ヤマハ製SB500のセットアップです。

    大きく順反りし弾き難い状態です。

    またトラスロッドのナットがナメており、回すのが危険な状態です。
    この頃のトラスロッドはエンド側にギブソンの様なナットが付いたパイプレンチ等で回すモデルとなります。
    前オーナーの扱いが酷かった様子で、ナットの角が丸まって殆どレンチが噛みません。

    ダメ元でしたが何とか外す事ができ、ナットの再利用は不可なので合うナットで代用した。

    消耗で音がビビる箇所がありますがある程度は弾けるレベルには調整のみで行えました。
    フレットすり合わせした方が良いレベルですが、この年代製は状態が悪くても当然と言えるので購入時は本体価格+リペア料金が掛かると思って購入した方が良いです。

    ありがとうございました♪


    This is a Yamaha SB500 setup.

    It is hard to play as it has a large forward bow.

    The truss rod nut is in a bad shape and it is dangerous to turn.
    The truss rod at this time is a model that is turned with a pipe wrench with a Gibson-like nut on the end side.
    The previous owner had treated the truss rod so badly that the nut’s corner was so rounded that the wrench would hardly bite.

    The nut was not reusable, so we substituted a matching nut.

    The sound was a little shaky due to wear and tear, but I was able to get it to a level where I could play it to some extent with just a few adjustments.
    It would be better to grind the frets together, but it is not surprising for a guitar of this age to be in poor condition, so you should expect to pay the price of the instrument plus repair fees.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250330_084904055.MP
  • Ibanez EHB1005F トラスロッドナット修正

  • 2025/06/15
  • Category:
  • アイバニーズ製EHBのトラスロッドの修正です。

    お客様のミスによりトラスロッドのナット口をナメさせてしまったとの事です。

    こちらで修正と言っても大した作業は行えませんが、チェックしてみると回す際にしっかりと工具を奥まで入れずに回した様子でナット入口付近だけがナメっている様子です。
    そのせいもあって工具が奥まで入らない状態です。

    多少の作業で奥まで入る様になり、工具を奥まで入れれば回せる様にはなりましたが元々この状態なので不安はある状態です。

    また両効きトラスロッドな事もありナット単体の交換は不可な物となります。

    トラスロッドをナメさせてしまう様な、特にトラスロッドに余裕が無く回すのが硬い状態は素人がナメさせやすい状態と思います。
    購入前にトラスロッドの余り量をチェックして購入するのはこの辺りにも重要になってきます。

    トラスロッドの余り量が多いと回す力もそこまで強く必要としませんのでナメさせる危険も少なくなります。
    近年は新品でもトラスロッドの余り量が少ない・限界で売られている事も多くなり、この辺りを全く表記しないので楽器屋で買う方が危険な時代です。

    必ず購入前に店員にトラスロッドの余り量を効く&必ず目の前で回して確認させる事を徹底して購入して下さい。
    また「弦の張りっぱなしで良い」とかその理由に「トラスロッドの張力でバランスしているから」等と言う楽器屋は地雷です。
    知識が無い事を露呈した言葉ですので、そうした楽器屋からも買わないで下さい。
    買った後のアフターサービスも知識が無いので非常に苦労する事となりますので要注意です。

    ありがとうございました♪


    This is a truss rod correction for an Ibanez EHB.

    The customer made a mistake and made the nut opening of the truss rod to be snapped off.

    We can’t do much work to fix it, but when we checked it, we found that only the entrance area of the nut was snagged because he didn’t put the tool in deep enough when he turned it.
    This is one of the reasons why the tool does not go all the way in.

    After some work, it was able to go all the way in and can be turned if the tool is inserted all the way in, but there is still some concern because of this original condition.

    Also, because the truss rod is double-acting, it is not possible to replace the nut alone.

    It is easy for amateurs to jam the truss rod, especially if the truss rod has no room and is hard to turn.
    It is important to check the amount of truss rod left before purchase.

    If there is a large amount of truss rod left, the turning force does not need to be as strong, so there is less danger of the truss rod being jammed.
    In recent years, even new instruments are often sold with a small amount of truss rod left over or at the limit, and it is more dangerous to buy them at a music shop because they are not marked with this information at all.

    Please make sure to ask the shopkeeper how much truss rod is left before you buy, and be sure to have the shopkeeper turn the truss rod in front of you to check.
    Also, a music shop that tells you that you can leave the strings taut and that the reason for this is because “the tension of the truss rod balances the strings” is a minefield.
    These words reveal a lack of knowledge, so please do not buy from such a music shop.
    After-sales service after purchase is also very difficult due to lack of knowledge, so be careful.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250225_131848038.MP
  • FenderCustomShop ストラトキャスター PU交換 KING TONE GUITAR BLUEBIRD J1 GUITAR PICKUPS

  • 2025/06/13
  • Category:
  • PXL_20250225_115718840.MP

    フェンダーカスタムショップ製ストラトキャスターのPU交換です。

    キングトーン製ブルーバードに交換です。

    50年代みたいな音、モッサリでレンジ狭いサウンド傾向です。

    レイヴォーンサウンドを再現したPUとの事ですがそうは聴こえず、むしろ50年代ストラトキャスターのサウンドに向いた音に聴こえます。
    ブルースに合いそうな音でもっさりと太い音が好みとするなら良いPUと思います。

    ありがとうございました♪


    PU replacement for a Fender Custom Shop Stratocaster.

    Replaced with King Tone Bluebird.

    It sounds like 50’s. It has a muffled and narrow range sound.

    It is said that this PU reproduced Rayvaughn sound, but it doesn’t sound like that, it sounds more like 50’s Stratocaster sound.
    If you like a fat sound, this is a good PU for blues.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250205_130149776
  • Futra MS800 カスタムオーダー セットアップ

  • 2025/06/10
  • Category:
  • フュートラ製のカスタムオーダーMS800のセットアップです。

    完成し届いた際に初期不具合で一度は国内工場に送って修理されたとの事で、状態チェックも含め持ち込まれました。

    一応は不具合を修正してもらったとの事ですがセレクター操作時に音切れがあったりする事、内部配線を触ったりすると音が出なくなる事を確認しました。
    配線にもミスあり、センターでフェイズアウト状態になるので配線ミスとハンダ付けが良くないのか上記の動作不良が起こったりする様子です。

    他にもブリッジのチューニングが不安定で、アームを使用しダウン/アップ時が実質使用不可(かなりチューニングが狂う、元の位置に戻らない)ので、セットアップのみの作業でアーム使用の際は使用が難しい状態と思います。

    調整で殆どトラスロッド限界に近くなりました。

    激安でオーダーできるギターですので価格を考えたら品質はそこまで求めてはいけないとは思いますが、ベトナム製との事でIVYやアジャイルと同じ感覚で買うメーカーかと思います。

    ありがとうございました♪


    This is a setup of a custom-ordered MS800 made by Futura.

    The unit had been sent to a domestic factory for repair due to initial problems when it was completed and received, and was brought in for condition check.

    We confirmed that the problem had been corrected, but that there was a sound cutoff when operating the selector, and that the sound would not come out if the internal wiring was touched.
    There is also a mistake in the wiring, and the sound phases out at the center, which may be caused by a wiring error and poor soldering.

    The tuning of the bridge is unstable, and it is practically unusable when the arm is used for down/up tuning (it is out of tune and does not return to the original position).

    It is almost at the truss rod limit with adjustment.

    I know I shouldn’t expect such high quality considering the price since I can order the guitar at a very low price, but it is made in Vietnam, so I think it is a manufacturer I would buy with the same feeling as IVY or Agile.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250206_122704508
  • FenderMexico テレキャスター フレットすり合わせ

  • 2025/06/08
  • Category:
  • フェンダーメキシコ製テレキャスターのフレットすり合わせです。

    消耗による音詰まり箇所がある状態です。

    フレットすり合わせのタイミングは基本的にフレット上面にへこみが出てきたタイミングで行った方が良いです。

    音が悪くなる事は当然ながら音程感が悪くなるので、楽器として使用するのはあまり良い事ではありません。

    フレットをすり合わせ問題が無い状態に修正しました。

    ありがとうございました♪


    This is a Fender Mexican Telecaster fret grinder.

    It is in a condition where there are sound clogging spots due to wear.

    Basically, it is better to perform fret fret fretting when dents appear on the top surface of the frets.

    The sound will naturally deteriorate and the sense of pitch will deteriorate, so it is not a good idea to use it as a musical instrument.

    We have corrected the problem by rubbing the frets together.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE