カテゴリー別アーカイブ: リペア

    PXL_20250317_103246290
  • Ibanez SIX7FDFM セットアップ

  • 2025/05/18
  • Category:
  • アイバニーズ製SIX7FDFMのセットアップです。

    弦高が低く音が詰まり気味の状態です。
    前オーナーの速弾き仕様になっているのか知りませんが余りにも弦高がベタベタに低いとまず鳴らすのが難しいです。

    適切な状態に調整し、特に不具合無く弾ける状態に仕上げました。

    低ければ低い程に弾き易くなりますが音質が失われていきますので、この辺りのバランスは人それぞれに好みがありますので自分に合わせた調整が正しい調整となります。

    ありがとうございました♪


    This is an Ibanez SIX7FDFM setup.

    The string height is very low and the sound is very clogged up.
    I don’t know if this guitar was designed for fast playing by the previous owner, but it is difficult to play if the string height is too low and sticky.

    We adjusted the strings to the proper height and made it playable without any particular problems.

    The lower the string height, the easier it is to play, but the more sound quality is lost, so the balance between the two is a matter of personal preference, so the correct adjustment is one that suits you.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    maxresdefault
  • 楽器業界でもAIが凄い!今更聞けない今後の視聴者に求められる事、無知はもう罪である。

  • 2025/05/16
  • Category:
  • AIが出てきて凄い進化をしているニュースは誰でも知っていると思います。

    楽器業界も例外ではなく、AIが活用され実際に私もYoutube動画製作にAIで全自動で製作した動画を上げ始めています。
    昔はショート動画でAI全自動を上げておりましたが、ちょっと生成動画の品質に問題が起きてました。
    それらは今でも見る事が可能です。

    今回はその「AI」から情報を得る事についての内容です。

    これらは今後AIが発信する事について「知らない・聞いてない」は通らない大事な話となりますので最後までご覧下さい。

    ~人間の判断次第で良くも悪くもなる~

    ショート動画の様なオマケという立ち位置ではなく本編動画としてYoutube動画を投稿する実験を行っています。

    実際にAIに動画を全自動で作らせ、視聴者にその反響を確認する実験を行っています。
    週一で水曜日に投稿予定です。

    AIの全自動で製作された動画は完璧な物ではありません。
    しかし驚きな事は「情報が的を得ている」のです。
    言葉足らずでただ見ただけでは分かり難いのも事実ですが、目線が違うとかなり濃い情報動画です。

    しかしこの的を得ているという判断も「情報がある人」だからできるのであって「情報が無い人」はその判断ができません。

    AI動画は現在実験という段階なのでコメントは良い内容も悪い内容も全て非表示にしていますがその辺りが面白く分断されています。

    例えば日々私のYoutubeやブログを読んでいるリスナー、つまりは情報強者は内容が読み解けると思います。
    そうした人達はAIが出す答えに私が日々出している発信と答え合わせができて面白いと思います。

    しかし逆に情報を何も持たない情弱はナメたコメントをしてきます。
    「AI動画で適当な動画を上げている」や「いつもと違い楽している、以前と違って浅い内容」等、全く見ている目線が違います。
    こうした人達は情報を持たないからこそ深層まで物事を見る事ができません。

    表現するならこの時点で「大きな情報格差」が起こっている事が分かるでしょうか?
    昔からそうですが、今後はAIを使用する人達によっても情報に大きな精度格差が起こるという事です。


    初心者が絶対に買ってはいけないギター5選!後悔してからでは遅い!これだけは絶対に購入前に確認しないと痛い目見ます! ギタークラフトマン&ギターリペアマンの話 Vol.AI-1

    ※AI動画はご自身で情報内容を精査して下さい。



    こちらが1本目に上げたAIの自動生成動画です。

    これを見てどう思いましたか?良い動画?クソ動画?

    どちらの判断になるかであなたの情報レベルが分かります。

    詳しくはこちらで解説してます。



    ■バカがより騙される世の中になる■

    恐ろしいのは今よりも犯罪が横行します。

    それは被害者が悪いのではなく、被害者が無知だから悪い事となります。

    闇バイトやパパ活が良い例です。
    そもそもやらなければ良いだけの話なのですが、それをやって騙された被害者面をしますがただの犯罪者達です。
    闇バイトもそもそも途中で気が付いたなら辞めれば良いだけ、パパ活なんて言葉を変えた売春婦(日本では犯罪)なのでやってる奴らは人として終わってます。
    決め付けた言い方にはなりますがこうした頭の人達にAIが与える情報を得てどの様に活用されるのでしょうか?
    大体はAIで生成した物凄く説得力のあるプレゼンに騙され新たな犯罪の犠牲者となる事でしょう。

    今後はAIであたかも真実で問題無いかの様な情報が出てきます。
    よりこうした手口の「いつの間にか犯罪行為をさせられていた」系の事件が起こるでしょう。
    AIが出した確実な未来!という形で絶対に儲かる投資ビジネス等も出てくるでしょう。
    しかしこれは知識が無い無知の人の責任でもあります。やらなければ良いだけ、それだけで犯罪組織を撲滅できる。
    やるバカが大勢居るから犯罪は無くなりません。

    ●AI動画はこうして見ろ!●

    AI動画は「知識がある人が見る物」です。
    極端に例えるなら小学生に東大生の勉強を教える様な物です。
    自分に合った知識レベルから時間を掛けて勉強していかないと簡単に間違った知識を刷り込まれます。

    AIで生成した動画なんてそもそも知識が無い人が見ても正しいかどうか判断ができないので、まず現段階ではAIの言葉のまま鵜呑みにしてると間違い無く間違った方向へ向かいます。
    いずれAI技術が進歩し人間の判断すら不要な世の中になってしまう事でしょうけど、今はまだその段階ではありません。

    「コスパ・タイパ」は仕事ができる人が使う言葉です。
    無知な人が時間を掛けて勉強せず、子供の時から全てAIの指示通りに動いて大人になったとしたらその人に何の価値がある人間になると思えるでしょうか?
    それこそそんな人なんてAIで代替した方が良いです。
    AIの指示通りに生きている人なんだからAIで代替も簡単でしょうに。
    AIに代替されないスキルを持たない人への価値が無い時代になります。

    いずれ知識格差はAIで埋まるでしょう。ただその知識を使う人がまともでないなら意味はありません。
    悪い話でも無く、これからは人間の価値だけで勝負できる良い時代になると思います。
    今までの学歴で人の価値を判断されるのは意味不明でありいびつな社会です。
    中卒だから、高卒だから、有名大学を出てないからと不当な判断をされた人も大勢居る事でしょう。
    しかし社会に出れば気が付きますが社会では「使える人間か?そうでないか?」が本質であり、そうした学歴の不当差別をAIで埋められる時代になると思います。
    知識に価値が無くなっていきます。

    そして今以上に無知な人と情報を持った人との差が広がり、貧富の格差は拡大するでしょう。
    「AIの性能が上がっていくから勉強しないで良いんだ!」は確かに間違い無いのですが、AIが出す言葉通りに行動して将来の保証は約束されていません。
    そのAIが出した答えを信用するかもその人の責任です。
    結局はその判断力、自分の知識や知能が必要になってきます。

    AI以前に私の情報でも良い楽器を手に入れる・正しい保管方法を行い長持ちさせ得を得る、既に私の発信を見てるか見てないかでその格差が起きているじゃないですか。
    得をするのか損をするのか、結局は自分次第です。

    ありがとうございました♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    IMG20241204164602
  • LaidBack テレキャスター ナット溝切り調整&配線直し&セットアップ Bare Knuckle Pickups The Boss

  • 2025/05/15
  • Category:
  • IMG20241203203924

    レイドバック製テレキャスターのナット溝切り調整・配線直し・セットアップです。

    ベアナックル製ザ・ボスに交換です。
    音はテレキャスターの基本形の様なサウンドで原点的、特に大きなキャラクター変化を感じないので個性の強いPUでは無さそうです。

    中古購入との事ですが最初からトラスロッドが殆ど限界状態、調整でトラスロッド限界となりました。

    10-52弦を使用、溝に入らなくなるので溝切りが必要になります。
    またナット溝の状態が高い所や極端に低い所があるのでかなり弾き易い状態です。
    溝切りし整える事で弾き易くなりましたが最初から極端に低い所は寿命の意味で長生きしません。

    配線が特殊でトーンに付いたミニスイッチでハムバッカーサウンドが出せるので通常のテレキャスターとは違う音を出す事が可能です。

    ありがとうございました♪


    Nut groove cut adjustment, rewiring and setup of a Laidback Telecaster.

    Replaced with a Bare Knuckle The Boss.
    The sound is like a basic Telecaster sound.

    The truss rod was almost at the limit from the beginning, and it was adjusted to the truss rod limit.

    It is necessary to cut the groove because the 10-52 string is used and it will not fit in the groove.
    Also, the nut groove has some high spots and some extremely low spots, so it is very easy to play.
    The groove cutting has made it easier to play, but the extremely low groove from the beginning will not last long in terms of longevity.

    The wiring is special and the mini-switch on the tone can produce a humbucker sound, which is different from a normal Telecaster.

    Thank you very much♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250306_124508410
  • Fender / Player Stratocaster Maple Fingerboard ストラトキャスター ナット交換&セットアップ curtis novak pickups

  • 2025/05/13
  • Category:
  • PXL_20250306_112904418

    フェンダーストラトキャスターのナット交換・セットアップです。

    ナット高が非常に高く弾き難い状態で、お客様の要望によりこの機会に溝切りよりも交換する事となりました。

    カーティスノバック製PUに交換です。
    こちらはかなり音質が良く、メンバーシップ限定動画にても紹介しておりますがお勧めです。

    メンバーシップ限定動画ではリペア現場で取り付けたパーツのレビュー等、一般動画で公開していない動画をアップしておりますのでご覧下さい。

    ありがとうございました♪


    This is a nut replacement and setup for a Fender Stratocaster.

    The nut height was very high and difficult to play. At the customer’s request, we decided to take this opportunity to replace the nut rather than cut a groove.

    We replaced the PU with a Curtis Novak PU.
    The sound quality is very good, and as shown in the membership-only video, it is highly recommended.

    Please check out our membership-only videos, which include reviews of parts installed at the repair site and other videos that are not available to the general public.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250223_090001566
  • FenderJAPAN テレキャスター PU交換&セットアップ

  • 2025/05/12
  • Category:
  • フェンダージャパン製テレキャスターのPU交換・セットアップです。

    メーカー不明だがお客様持ち込みPUに交換しました。

    フロントは明るめで音抜けが良く、リアは硬く無く音の分離も良いサウンドです。

    90~2000年代フェンダージャパン製と思いますがトラスロッドも多少は余りがあり、音も良く良好個体です。

    フレットの消耗が凄いのですり合わせした方が良い状態ですので正しく使用したくなりましたらすり合わせをお勧めします。

    ありがとうございました♪


    This is a PU replacement and setup for a Fender Japan Telecaster.

    The PU was replaced with a PU brought in by the customer, though the manufacturer is unknown.

    The front is bright and has good sound, and the rear is not hard and has good sound separation.

    The truss rod has a little extra room and the sound is good.

    The frets are very worn and should be grated.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250315_083839319
  • Ibanez RG460DX-ROM Roadster Orange Metallic RG セットアップ

  • 2025/05/11
  • Category:
  • アイバニーズ製RG460DXのセットアップです。

    新品で購入したが音詰まり箇所があり調整に持ち込まれました。

    状態を確認すると4フレットで音詰まりが発生しており、5フレットだけ高い状態で4フレットが音詰まりする状態です。

    新品でもこうした不具合があるまま平気で販売されている事があるので、購入前に店員にチェックさせて買うのは当然ですがお店側が素人だと不具合に気が付きません。

    酷いお店だと初期状態の弦高が高く、弦高を高くすれば不具合箇所が誤魔化されるので音詰まりが分かり難くなります。
    なので弦高が高い時点で疑った方が良いです。
    購入後に指摘しても「当店での基準はこの弦高で不具合が出なければ問題無いと判断してます。」と誤魔化されて終わりです。

    不具合箇所が分かれば新品なら1年保証等が付いているので、基本は早い方が良いですが不具合を発見した際は購入店に申し出て直してもらいましょう。

    ただし相手が素人過ぎるとこうした圧倒的に誰でも分かる不具合ですら店員が不具合を分からない現象が起きて対応してくれない事が出てきます。
    実際にこの個体はリピーターのお客様のギターの為、後日に別のギター持ち込み時にお客様からこのギターは初期不良で返品した報告を聞いた際の購入した楽器店のやり取り話を聞きました。

    この音詰まりする状態でも楽器店側は「メーカーが送ってきた状態なので、状態は基準の範囲で問題無い」との事や「他リペアショップでチェックさせても構わない」とまで言われたそうです。
    ちなみにギター本体はお店に送ってあり店員が確認した状態での連絡です。そのやり取りメールも確認しました。

    私のお店でチェックした事はお客様が購入店に伝えてなかったそうですが、楽器店側の素人さがここまで来てると買うのが危険なレベルになっています。
    この個体はそこまで高額なモデルではありませんが、万が一高額なモデルを購入してアフターサービスがここまで酷いと楽器は楽器屋で買う事が難しくなってきます。

    楽器屋で買う際も基本的に知ってほしい知識としてちゃんと調整した上で渡してもらう事、トラスロッドの余り量を確認させる事、そもそも新品でトラスロッドの余り量を表示しないなら買わない事、不具合が起こった場合はどの様な対応をするのか必ず確認する事です。

    今回は何度もメールのやり取りの上でやっと返品できたレベルとの事で、明らか商品に不具合があるのに返品する事すら困難という事例をお客様から見せてもらいました。

    楽器屋をやってる人達へ向けて、もう少し自分の仕事にプライドを持って下さい。
    金儲けしか考えていないならこの仕事を辞めて下さい。業界として害悪な存在です。
    人が泣いて金を儲けてるなら仕事としてのやり方が完全に間違っています。
    良い仕事をして喜ばせた対価としてお金を稼いで下さい。

    ありがとうございました♪


    This is a setup for an Ibanez RG460DX.

    It was purchased new but brought in for adjustment due to a jammed part.

    The condition of the guitar was confirmed to be clogged at the 4th fret, with only the 5th fret being high and the 4th fret being clogged.

    It is natural to have the store staff check the guitar before buying it, but if the store is an amateur, they will not notice the problem.

    If the shop is not a good store, the initial string height will be high, and if the string height is high enough, the defect will be disguised, so it will be difficult to recognize the sound clogging.
    Therefore, it is better to be suspicious when the string height is high.
    If you point this out after purchase, you will be misled and end up saying, “Our standard is that if there is no problem at this string height, we judge that there is no problem. If you point out the problem after purchase, you will end up being misled.

    If you find a problem, it is better to report it to the store where you purchased the instrument and have it fixed.

    However, if the store is too much of an amateur, there may be a phenomenon that the store staff does not understand the problem, even if the problem is overwhelmingly obvious to anyone else, and they may not be able to fix it.
    In fact, this guitar belongs to a repeat customer, and I heard a story about an exchange at the music store where the customer brought in another guitar and later heard a report that this guitar had been returned due to initial defects.

    Even with this clogged condition, the music store said that the condition was within the standard range because it was sent by the manufacturer, and that they were even willing to let another repair store check it out.
    Incidentally, the guitar itself was sent to the store and the store staff checked it. I also confirmed the email exchange.

    I heard that the customer did not tell the store of purchase that he had checked it at my store, but the amateurishness on the part of the music store has reached such a level that it is dangerous to buy it.
    Although this unit is not that expensive model, if you buy an expensive model and the after-sales service is this bad, it will be difficult to buy a musical instrument at a music shop.

    When buying from a music shop, the basic things you need to know are that you should have the instrument adjusted properly, that you should check the amount of truss rod left, that you should not buy a new instrument if it does not show the amount of truss rod left, and that you should always check what they do in the event of a problem.

    In this case, the customer told us that he was able to return the instrument after many emails, and that he found it difficult to return the instrument even though the product was obviously defective.

    To those who are in the music store business, please have a little more pride in your work.
    If all you care about is making money, get out of the business. You are a detriment to the industry.
    If you are making money by making people cry, you are doing your job completely wrong.
    Please do a good job and make money in return for pleasing people.

    Thank you.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250426_094959314
  • Squier by Fender Classic Vibe 60s Stratocaster セットアップ

  • 2025/05/07
  • Category:
  • Youtubeでも紹介しましたスクワイヤー製クラシックヴァイヴ60年モデルストラトキャスターのセットアップです。

    2025年製の新品です。
    こちらの個体は特に初期状態でも不具合が無く、調整初期状態も他メーカーと比べ良かったです。
    トラスロッドの余り量も充分にあり良好な個体でした。

    調整してみると弾き易く、何よりも音が良い事が驚きです。
    約6万円のモデルですがサウンド面では高価格帯と大きくは変わらないと思います。

    ナット高も低めで弾き易く、フレットサイドの処理も低価格帯としても丁寧な部類です。
    音質も良いとなれば低価格帯ではかなり勧められますね。

    詳細についてはYoutubeにも動画を上げておりますので参考下さい。

    ありがとうございました♪



    This is a Squier Classic Vibe ’60 Stratocaster setup as featured on Youtube.

    It is brand new, made in 2025.
    There were no problems with this one, especially in the initial state, and the initial state of adjustment was better than other makers.
    There is enough truss rod left over and it is in good condition.

    After adjustment, it was easy to play and the sound was amazingly good.
    It is a 60,000 yen model, but in terms of sound, I think it is not much different from higher-priced models.

    The nut height is low, making it easy to play, and the fret side treatment is also very well done, even in the low price range.
    The sound quality is also good, which is highly recommended in the low price range.

    For more details, please refer to the video on Youtube.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250210_082856097
  • Gibson USA SG ネック割れ修正

  • 2025/05/06
  • Category:
  • PXL_20250209_104508836

    ギブソン製SGのネック割れ修正です。

    ヘッドの接着面に亀裂が入っている状態、3Pマホガニーネックです。
    特に割れも酷い状態ではないのでそのまま使用していても問題無さそうですが、要望により接着する事となりました。

    また配線にミスがある様でセンターでフェイズアウトする状態です。

    古い年代製に多い事ではありますがこちらはトラスロッドの効きがおかしいです。
    内部のトラスロッドに不具合がありそうで調整後に弦高が変わる(反りの状態が変わる)ので、内部でのトラスロッドの引っ掛かりが悪い様子です。
    ある程度触っていると落ち着いてきますが、状態としては不安でしかありません。
    こうした状態は最悪トラスロッドが効かなくなる事もあるので、作りが悪いメーカー品を購入するという事はこうした不具合が起こってくる事も理解しないといけません。

    こうしたメーカーがある事から「トラスロッドを一気に回したら壊れる」という間違った知識が広まっています。
    トラスロッドを回した事が悪いのではなく、回しただけで壊れる様な作りをしている事が問題です。
    当然ながらこうした事がリペアで私が触って起きたとしても責任を取る事は致しません。
    メーカーの問題なのと、こうした知識を持っていないお客様の問題です。
    そうしたトラブルにならない様に理解して購入した方が良いです。

    ありがとうございました♪


    This is a Gibson SG neck crack fix.

    The head has a crack on the gluing surface, and the neck is made of 3P mahogany.
    The crack is not so bad, so it seems to be OK to use it as it is, but we decided to glue it back together by request.

    Also, there seems to be a mistake in the wiring and it phases out at the center.

    The truss rod is not working properly, as is often the case with older models.
    The internal truss rod seems to be defective, and the string height changes after adjustment (the state of warping changes), so the truss rod is not hooked properly inside.
    It will settle down after some touching, but the condition is only uneasy.
    In the worst case scenario, the truss rod may stop working, so it is important to understand that purchasing a poorly made product from a manufacturer can lead to this kind of problem.

    Because of the existence of such makers, the false knowledge that “turning the truss rod all at once will break it” is widespread.
    The problem is not that turning the truss rod is bad, but that the truss rod is made in such a way that it can be broken just by turning it.
    Of course, I will not take responsibility if such a thing happens when I touch the truss rod for repair.
    It is the manufacturer’s problem and the customer’s problem who does not have such knowledge.
    It is better to buy with understanding to avoid such problems.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250203_111806340
  • Martin 00-15M 弦高調整

  • 2025/05/04
  • Category:
  • マーチン製00-15Mの弦高調整です。

    新品購入との事ですが弦高が非常に高くお客様がまともに弾けないとの事、なんと12F上で4.5mmもありお店側もよくこの状態で平気で売れたなと思います。

    トラスロッドの余裕少ないので、新品時点でこの状態なら今後長持ちする事も見込みが低そうです。

    こちらは30万円?(https://www.martinclubjp.com/guitars/15_series/00-15M/)のモデルかと思われますが、30万円で買ってこの状態なら結構お店も考えた方が良いと思います。

    ネックの反り調整とサドルを削り弦高を下げる事でまともに弾ける弦高に仕上げました。

    本来なら購入時にチェックしてこの辺りを店員に伝えて直してもらうか他のモデルを買うべきですのですが、素人だと分からない事と店員に「こういうものですよ」とか言われると信じて買ってしまうのが問題です。

    客側が知識を付ける事は当然として、お店側は状態が悪い物を平気で売らない事と正しい知識がある店員を配置すべきでしょう。
    こうした事があるから私は「楽器は楽器屋で買ったら危険」と言う事になります。
    誰もが安心して購入できる場所を業界が努力して作って下さい。私は環境がそうなる事を望みます。

    ありがとうございました♪


    This is a Martin 00-15M string height adjustment.

    The customer said that he bought it new, but the string height is so high that he can’t play it properly.

    The truss rod has little room to spare, so if it is in this condition when it is new, it is unlikely to last long in the future.

    This one seems to be a 300,000 yen () model. (https://www.martinclubjp.com/guitars/15_series/00-15M/) model, but if it was bought for 300,000 yen and in this condition, I think the store should think twice.

    We have adjusted the warp of the neck and lowered the string height by shaving the saddle to make it playable.

    Normally, you should have checked the guitar at the time of purchase and told the store staff about this and asked them to fix it or buy another model, but if you are an amateur, you don’t understand and if the store staff tells you “this is the way it is,” you will believe them and buy the guitar.

    It is a matter of course for the customer to be knowledgeable, but the store should not sell items in bad condition without hesitation, and the store should have staff with the correct knowledge.
    Because of these things, I would say, “It is dangerous to buy musical instruments at a music store.
    The industry should work hard to create a place where everyone can buy music instruments in a safe environment. I hope the environment will be like that.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250201_082641549
  • Epiphone Les Paul Custom EMG配線直し

  • 2025/05/02
  • Category:
  • エピフォン製レスポールカスタムの配線直しです。

    お客様の方で接続ミスされている状態です。またブリッジアース線が短く切られ接続されていたりと不具合があります。

    EMGはコネクタで簡単に接続できる様に思いそうですがセレクターの配線やアース線等の接続は手作業で行わないといけないので、いきなり初心者がやる作業としてはミスが起こり易いです。

    コネクタも表と裏とでどちらでも挿せるのでミスが起こり易いです。
    片方に突起がある等して付くようにしか付かない仕様にすればコネクタの接続ミスも起こりませんがメーカーが不親切です。

    ミスの箇所を修正し問題無く音が出せる状態になりました。

    ありがとうございました♪


    This is a rewiring of an Epiphone Les Paul Custom.

    The customer has made a connection error. Also, the bridge ground wire was cut short and connected.

    It seems that EMG can be easily connected with connectors, but wiring of selector and connection of ground wire have to be done by hand, so it is easy to make mistakes for beginners.

    However, it is easy to make a mistake as a beginner because the connectors can be inserted from either the front or the back.
    If the connector has a protrusion on one side so that it can only be attached in the way that it is supposed to be attached, connector connection errors would not occur, but the manufacturer is not very kind.

    I fixed the mistake and now I can play the sound without any problem.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE