タグ別アーカイブ: ストラトキャスター

    IMG20241005173308
  • Fender Custom Shop Custom Deluxe Stratocaster セットアップ

  • 2024/12/22
  • Category:
  • フェンダーカスタムショップ製ストラトキャスターのセットアップです。

    大きく順反りし弾き難い状態です。

    木材が珍しい仕様で現行品でも中々見られないモデルです。

    ボディ材はメイプルトップにマホガニー?バック。正確にはバック材は調べると「OKUME」という材でした。
    リアにもトーンが効く仕様です。

    PUがFat’50が付いてるが全然そんな音がしない。
    音がかなり良い個体です。
    耳に痛くない上に各PUのバランスがハーフトーンも含め良いサウンド。
    ストラトはハーフトーンで良い音が出せれば良いストラトですが、それに加えて各ポジションのサウンドが良ければ最高です。
    このストラトはまさにそれです。

    そしてハーフトーンの引っ込みも無く綺麗に鳴るのでこれは非常に良い個体ですので手放さない方が良いでしょう。

    ありがとうございました♪


    This is a Fender Custom Shop Stratocaster setup.

    It has a large forward bow and is hard to play.

    The wood is very rare, and you don’t see this model very often even in the current lineup.

    Body material is maple top and mahogany? Back. The back material is called “OKUME”.
    The rear has a tone effect.

    Fat’50 PU is attached, but it doesn’t sound like that at all.
    It is a very good sounding unit.
    It doesn’t hurt my ears and the balance of each PU sounds good including halftone.
    A Strat is a good Strat if it can sound good with halftone, but it would be great if each position sounds good in addition to that.
    This strat is just that.

    And it sounds beautifully without any halftone retraction, so this is a very good unit and you should not let it go.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240908210438
  • Xotic ストラトキャスター フレットすり合わせ

  • 2024/12/09
  • Category:
  • エキゾチック製ストラトキャスターのフレットすり合わせです。

    全体の消耗が大きく音詰まり箇所がある状態です。
    こうした状態は基本的にまともに使えません。
    音詰まりが出ない様にするにも調整だけでは限度があります。
    すり合わせしないといけないラインは目で見て分かるフレットの減りが出てきたら作業する必要があります。

    フレットをすり合わせる事で弾き易く問題が無い状態に仕上げる事ができました。

    エキゾチック製は音も良く弾き易い個体が多いのでギターもベースもお勧めなメーカーです。

    ありがとうございました♪


    This is an exotic Stratocaster fret grinder.

    The overall wear and tear of the guitar is significant, and there are some clogged areas.
    This condition is basically unusable.
    There is a limit to the amount of adjustment that can be done to prevent the fret jamming.
    The fret fret adjustment is necessary when there is visible fret wear.

    By grinding the frets, we were able to finish the fretboard to a state where it is easy to play and there are no problems.

    We recommend Exotic for both guitars and basses because many of their guitars and basses sound great and are easy to play.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240603194102
  • バッカス ストラトキャスター フレットサイド処理&セットアップ ローステッドメイプル

  • 2024/12/03
  • Category:
  • バッカス製ストラトキャスターのフレットサイド処理・セットアップです。

    低価格帯モデルはどうしてもフレットのサイド処理が甘く、手に当たって痛い等が上げられます。

    しかし低価格帯ではコストの面で人が手間暇を掛けないといけない作業は省略・最小限で済ませている事が多い為、この辺りが使用していて気になるなら直さないといけません。
    フレットサイド処理が良くできている価格帯は10万円台後半辺りからだと思いますので、実質低価格帯ではフレットサイド処理は良くできていないと判断して問題無いです。

    フレットサイド処理を行うと状態が物凄く良くなります。
    特に使用してきたなら猶更分かる変化です。まるで別物になります。
    それだけフレットサイドは演奏に影響を及ぼす所なので、ここに手間暇を掛けて仕上げるにはちゃんと意味があります。

    順反り状態を調整しましたがトラスロッドの余り量が残り少ないです。
    こちらはローステッドモデルですが、未だにプロでもリペアマンでも「ローステッドネックは安定して反らない」とかオカルト陰謀論者も多いです。
    現実では普通に反りますので、本気でそんな事を言ってるリペアマンに仕事を頼まないで下さい。

    音が良いのでフレットサイドの不具合が無くなったこの個体は元が2万円のモデルとは普通に思えないギターに生まれ変わりました。

    ありがとうございました♪


    This is a fret side treatment/setup for a Bacchus Stratocaster.

    Low-priced models tend to have poor fret side treatment, which can be painful to the hand.

    However, in the low price range, the work that requires a lot of time and effort is often omitted or minimized due to cost, so if this area bothers you, you need to fix it.
    The price range where fret side treatment is well done is from the upper 100,000 yen range, so there is no problem in judging that fret side treatment is not well done in the lower price range.

    Fret side treatment will improve the condition of the fretboard tremendously.
    Especially if you have been using it for a long time, you can see the change. It will be like a different instrument.
    Fret side affects the performance so much that it makes sense to spend a lot of time and effort to finish it.

    The truss rod has been adjusted, but there is not much left in the truss rod.
    This is a low-stud model, but there are still many occult conspiracy theorists among professionals and repairmen who say that low-stud necks are not stable and do not warp.
    In reality, they usually warp, so please don’t ask a repairman who seriously says such a thing to do his work.

    The sound is good and the fret side defects are gone, and this piece has been reborn as a guitar that does not seem normal for a model originally priced at 20,000 yen.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240720181540
  • FenderCustomShop ストラトキャスター ジャック交換&セットアップ

  • 2024/11/14
  • Category:
  • フェンダーカスタムショップ製ストラトキャスターのジャック交換・セットアップです。

    ジャック不良でまともに音が出ない状態です。
    ジャックは消耗品で一番楽器で消耗するパーツですので使用頻度にもよりますが1年単位で交換した方が良いと思います。

    他にも順反りで弾き難い状態を調整し弾き易くしました。

    高額な楽器でも特別凄いパーツが付いている等ではなく、パーツは他ブランドと同じく消耗しますので使用頻度が高いギターのパーツはガリが出たタイミングで交換した方が良いです。

    ありがとうございました♪


    This is a jack replacement and setup for a Fender Custom Shop Stratocaster.

    The jack is defective and not producing proper sound.
    The jack is a consumable part and is the most worn part of the instrument, so it is recommended to replace it every year, depending on how often it is used.

    We have also adjusted the warp to make it easier to play.

    It is not a very expensive instrument with special parts, but the parts will wear out just like any other brand, so it is better to replace the parts of a guitar that is used frequently at the time when the buzzing appears.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240714174805
  • SVL ストラトキャスター セットアップ

  • 2024/11/06
  • Category:
  • SVL製ストラトキャスターのセットアップです。

    トラスロッドが殆ど限界状態です。
    トラスロッドを回してみるとが半周程度しか回らない状態です。
    限界付近と思っていましたがユルユル状態から限界になる範囲が半周程度しか回らない、一応はこの半周の範囲でも意外に反りが効くが回す範囲が異常に少ないので限界近い事には変わりません。

    また音が良いモデルで珍しいメーカーという事もあり今後触る個体等でもデータを集めたいブランドです。
    トラスロッドも特殊な埋め込み・トラスロッド自体が特殊等の可能性もあるので、本数を触ればこれが普通なのか異常なのか分かるでしょう。

    ありがとうございました♪


    This is an SVL Stratocaster setup.

    The truss rod is almost at its limit.
    When I tried to turn the truss rod, it only turns about half way.
    I thought it was near the limit, but the range where it goes from loose to tight is only about a half turn.

    The sound is also good, and the brand is a rare maker, so we would like to collect data on the individual pieces that we will touch in the future.
    There is a possibility that the truss rod itself has a special embedding, so if you touch a few pieces, you will know if this is normal or abnormal.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240714203828
  • Shijie ストラトキャスター セットアップ STE-V CUSTOM

  • 2024/10/31
  • Category:
  • シージェ製ストラトキャスターのセットアップです。

    中国のハイエンドギターブランドとの事です。

    初めて触りましたが作りが良く弾き易い、ワーモスを組んだかの様な仕様ですが値段が安過ぎです。

    値段を考えたら非常に高いコストパフォーマンスですので、日本に流通してくると他メーカーも中々無視できない存在になってくると思います。

    高額なのに質が低いメーカーが増えてきましたが、今後ブランドだけで物を売るのは厳しくなってくると思います。

    ありがとうございました♪


    This is a Stratocaster setup made by Sije.

    It is a high-end guitar brand from China.

    I touched it for the first time, and it is well made, easy to play, and has specifications as if it were assembled from Warmoth, but the price is too low.

    Considering the price, the cost performance is very high, so I think other makers will not be able to ignore it when it is distributed in Japan.

    I believe that it will become tougher to sell products only by brand in the future, although the number of expensive but low quality manufacturers is increasing.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240629184214
  • Greco ストラトキャスター セットアップ

  • 2024/10/22
  • Category:
  • IMG20240629180914

    IMG20240629180922

    Gnecoロゴ時代のグレコ製ストラトキャスターのセットアップです。

    音が良く、ノーマルで付いているPUの様子だが音が非常に良いモデルです。
    当時の低価格帯は恐ろしい位に音は良いですね。

    またこの年代で既にPUのポールピースを整える概念はあった事が分かりました。
    何故にこの状態が廃れたのか、疑問でしかありません。

    ありがとうございました♪


    This is a Gneco Stratocaster setup from the Gneco logo era.

    This model has a good sound, and the PU looks but sounds very good with the normal PU attached.
    The sound is good enough to be scary for the low price range at that time.

    I also found that the concept of aligning the PU pole piece was already in existence at this age.
    I can only wonder why this condition was discontinued.

    Thank you very much


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240607214754
  • FenderJAPAN ストラトキャスター フレットすり合わせ&ジャック交換

  • 2024/10/11
  • Category:
  • フェンダージャパン製ストラトキャスターのフレットすり合わせ・ジャック交換です。

    フレットが全体的にかなり消耗が大きい状態です。
    当時のフェンダージャパン製は特に古い年代でなくても音が良いモデルが多いので、数万円のモデルで現在でも使用を続けている人も多いと思います。

    それに伴って消耗具合も大きい物が多いので注意が必要です。

    2000年中期位のモデルだがトラスロッドの余り量が多く状態が良いです。
    08-38弦で使用していたそうで、細いゲージは当然ながらネックに対する負荷が少ないので順反り防止としても好都合です。

    多くの楽器は順反りしトラスロッドに余裕が無い・限界状態の物も多いので、長持ちさせるにはどれだけネックに負荷を与えずに使用を続けるか?が重要になっていきます。

    ありがとうございました♪


    This is a Fender Japan Stratocaster fret grating and jack replacement.

    The frets are generally in a very worn condition.
    Many of the Fender Japan made Stratocasters of that time sounded good even if they were not old, so there are many people who continue to use them even now with models priced at tens of thousands of yen.

    Many of them are still in use today, and many of them are still in good condition.

    This model is about mid-2000, but it is in good condition with a lot of truss rod left over.
    The instrument was used with 08-38 strings, and a thin gauge naturally puts less load on the neck, which is good for preventing forward warpage.

    Many instruments are warped and have no room in the truss rod or are at their limit. It is very important to keep the neck unloaded for longevity.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240610174643
  • FenderUSA ストラトキャスター 配線直し&セットアップ Seymour Duncan SSL-1 SSL-5

  • 2024/10/07
  • Category:
  • フェンダーUSA製ストラトキャスターの配線直し・セットアップです。

    フロント・センターにSSL-1、リアにSSL-5に交換されております。

    お客様が交換作業をして音がおかしいとの事で持ち込まれましたが、配線を失敗している状態です。

    配線を直し音を出してみると良いサウンドです。

    ダンカン製シングルコイルは優秀で、低価格で買えるPUの中でもお勧めできるモデルが多いですが近年は値上がりでその手軽に音を良くする手段として難しくなってきています。
    SSL-1も音が良くて3年程度前までならサウンドハウスで1個6980円等で販売されていた事もありました。
    シングルコイルならまずSSL-1に交換して、その音からダンカンのカタログを参考に別PUに交換する等すると結構ハマります。
    ダンカンのカタログは結構PUの説明精度が高いです。

    ありがとうございました♪


    This is a Fender USA Stratocaster rewired and setup.

    It has been replaced with an SSL-1 front and center and an SSL-5 rear.

    The customer brought it in because the sound was not right after the replacement work, but the wiring had failed.

    After rewiring and trying the sound, it sounds good.

    The Duncan single coils are excellent, and there are many models among the low-priced PUs available that I can recommend, but in recent years the price has gone up and it has become more difficult to find an easy way to improve the sound.
    The SSL-1 also has a good sound, and up until about 3 years ago, it could be found at Soundhouse for 6980 yen per unit.
    If you want to use a single coil, you should first replace it with an SSL-1, and from the sound of the SSL-1, you can change to another PU by referring to Duncan’s catalog.
    Duncan’s catalog is quite accurate in explaining PUs.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240614204316
  • FenderJAPAN STD-57 ナット交換&フレットすり合わせ&セレクター交換&ジャック交換

  • 2024/10/02
  • Category:
  • フェンダージャパン製ストラトキャスター、STD-57のナット交換・フレットすり合わせ・セレクター交換・ジャック交換です。

    かなり消耗が大きい個体です。

    細かくはフェンダージャパンでは無い様子でネックは別メーカーの物に交換されている様子(ボディのネックポケットにSTD-57表記)、ネックポケットとネックの相性が悪くシムは計4枚入れて調整・ネックポケットはガバガバ状態です。とりあえず弾く分には問題ありません。

    消耗箇所を修理し音も安定して出せる状態に修正しました。
    音が太く煌びやかでレンジ感があり良い個体です。
    意外とギターは不思議とカッチリ丁寧に作られた物よりも隙間もあって雑な作りの物が音が良かったりします。

    特にネックはボディに付かない方が音が良い傾向に思います。
    具体的には左右がガバガバ、シムも複数入れないと弦高がダメな物はネックとボディに隙間が大きく殆ど触れていない状態になります。
    ネックとボディは違う木材なので、その振動数が合わないのも当然で楽器としての組み合わせは基本違う材なら相性は悪いと思われます。
    距離が離れて弦振動が干渉しない位の隙間がある方が音が良くなるのも理解はできるかと思います。

    また08-38弦で使用し続けているとの事でトラスロッドの余り量もかなりある状態です。
    ただ動く範囲が狭いですが効きは良いです。
    ネックはメーカー不明ですがトラスロッドが回る範囲から古い国産なのかもしれません。

    細いゲージを使用しネックに強い負荷が掛からない状態なら順反りし難いのは当然です。
    長持ちさせるにはこうした配慮も必要です。

    ありがとうございました♪


    This is a Fender Japan Stratocaster, STD-57, nut replacement, fret grind, selector replacement, and jack replacement.

    This is an individual with quite a bit of wear and tear.

    The neck was replaced with another maker’s neck (STD-57 is marked on the body neck pocket), and the neck pocket and neck are not compatible. The neck pocket is in a state of disarray.

    The wear and tear has been repaired and the sound is now stable.
    The sound is fat and shiny with a good range.
    Surprisingly, guitars that have gaps and are not well made sound better than guitars that are well made.

    In particular, the neck tends to sound better when it is not attached to the body.
    Specifically, if the neck is too loose on both sides and the strings are too high without multiple shims, there is a large gap between the neck and body, and they are hardly touching.
    Since the neck and body are different woods, it is only natural that their vibration frequencies do not match, and the combination as an instrument is basically incompatible with different woods.
    It is understandable that the sound would be better if the strings were far enough apart so that their vibrations do not interfere with each other.

    Also, since you have been using it with 08-38 strings, there is quite a bit of truss rod left over.
    The range of movement is narrow, but it works well.
    The maker of the neck is unknown, but it may be an old domestic one from the extent to which the truss rod turns.

    If a thin gauge is used and the neck is not under a heavy load, it is natural that it is hard to warp in order.
    This kind of consideration is necessary to make the neck last longer.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE