タグ別アーカイブ: ストラトキャスター

    IMG20240526175727
  • フジゲン ストラトキャスター セットアップ

  • 2024/09/22
  • Category:
  • フジゲン製ストラトキャスターのセットアップです。

    ダンカンPUが付いたコストパフォーマンスが高い機種ですね。

    順反りして弾き難い状態を調整しました。

    調整する事で音も良く弾き易くなりました。
    フジゲン製は低価格帯でもしっかりと精度が高く作られており、トラスロッドも良く効くのでフェンダー等と比べたら反り調整の範囲は下手すると2~3倍は違うかもしれません。

    こうしたモデルも数万円で購入できるので、フジゲン製はコストパフォーマンスが高いです。
    中古市場も値付けが甘いというか、比較的安価で状態が良い物を手に入れられる印象があります。

    ありがとうございました♪


    This is a Fujigen Stratocaster setup.

    It is a cost-effective model with Duncan PU.

    We have adjusted the warped and hard to play condition.

    After the adjustment, the sound is better and easier to play.
    Fujigen’s low-priced models are made with high precision and the truss rod works well, so the range of warp adjustment may be two or three times larger than Fender’s. These models can be purchased for several tens of thousands of yen.

    Since these models can be purchased for tens of thousands of yen, Fujigen’s products have a high cost-performance ratio.
    I have the impression that the used market is also not so pricey, or you can get one in good condition at a relatively low price.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240516201752
  • Fender Custom Shop ストラトキャスター セットアップ

  • 2024/09/19
  • Category:
  • フェンダーカスタムショップ製ストラトキャスターのセットアップです。

    順反りして弾き難い状態です。

    ネック反りを調整して弾き易くなりました。

    フェンダー系はトラスロッドの効きが悪い為、少し回す程度ではあまり反りが変化しませんので多めに回す意識で調整した方が上手くいきます。
    つまりはトラスロッド限界にも近くなるので、弦を緩めて湿度を良い数値に管理していないと長持ちできないとも言えます。

    アビゲイルイバラPUが付いているそうで、ストラトらしさは勿論ですが音抜けも良くコード鳴りも良い個体でした。

    ありがとうございました♪


    This is a Fender Custom Shop Stratocaster setup.

    It is hard to play due to forward warp.

    The neck warp has been adjusted to make it easier to play.

    Fender Stratocaster has a bad truss rod, so you can’t change the warp by turning the truss rod a little bit.
    In other words, it is close to the truss rod limit, so it is necessary to loosen the strings and control the humidity to a good value to make it last longer.

    It has an Abigail Ibarra PU, and of course it has a Strat-like sound, but it also has a good sound through and good chord sound.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240515180339
  • FenderUSA ストラトキャスター セットアップ

  • 2024/09/17
  • Category:
  • IMG20240515174031

    フェンダーUSA製ストラトキャスターのセットアップです。

    これはご自身で改造された物?元からこの仕様?なのか不明ですが珍しいスプリングの仕様です。

    また古いエリッククラプトンモデル?と思っていたらパッシブ仕様のモデルです。

    通常のトーンが真ん中にあり、TBXトーンがセンターとリアに効く様に配線されています。
    恐らく中身もイジられていそうです。

    音は良いが状態悪いです。
    元からトラスロッドの余裕が無く大きく順反りしており、ロッドを限界まで回しても少し順反り気味です。
    弾けなくはないが全体的に弦高が高くチョーキングで音詰まる所があるのですり合わせ等は行った方が良いかもしれません。

    ただトラスロッド限界状態で弦を張ると少し順反り状態なので、直して使い続ける事を考えるとネックはダメそうとも判断できます。
    本当はこうした状態にならない様に日々弦を緩めて保管しておかないといけませんが、中古入手ではトラスロッドの余り量が多い物を見つけて買う事が重要です。

    ありがとうございました♪


    This is a Fender USA Stratocaster setup.

    Is this something you modified yourself? Or was it originally made this way? It is unknown if this is the original setup or not, but it is a very rare spring setup.

    Another old Eric Clapton model? I thought it was an old Eric Clapton model, but it is a passive model.

    The normal tone is in the middle, and the TBX tone is wired to the center and rear.
    It looks like the inside has probably been messed with as well.

    It sounds good but is in poor condition.
    The truss rod is bent forward a lot, and even when the rod is turned to the limit, it is still bent forward a little.
    It is not unplayable, but the overall string height is high and there are places where the sound gets stuck when chalking, so it may be better to do some adjustments.

    However, when the strings are stretched at the limit of the truss rod, the neck is a little warped, so it is possible to judge that the neck is not good enough to continue to use it.
    I really need to keep the strings loose daily to avoid this condition, but it is important to find and buy a used one with a large amount of truss rod left over.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240411213546
  • Emotion ストラトキャスター ナット溝切り調整&フレットすり合わせ&ポット交換 VANZANDT VINTAGE PLUS

  • 2024/08/30
  • Category:
  • エモーション製ストラトキャスターのナット溝切り調整・フレットすり合わせ・ポット交換です。

    音詰まり箇所があり状態悪いです。弾き込まれていればどうしてもフレットはすり減りますので修理が必要になってきます。

    ヴァンザント製ヴィンテージプラスに交換、ボリュームにガリで交換しました。

    IMG20240410174001

    お客様の方で3弦6弦が引っ込められてて、バランスが良いサウンドになっています。

    シングルコイルは未だに弦の音量バランスが悪く、メーカーも素人だったりするのでその異常に気が付かず昔の仕様のまま今に至っている物もかなり多いです。

    この弦の音量バランスは非常に重要で、特にギターはコードで鳴らす事が多いのでその弦の音量が合っていないとすれば音が大きい弦が強調され音が小さい弦が聞こえ難くなりミュート気味・鳴りが甘い様な音になるので結果としてコードが綺麗に鳴らなくなります。

    PUを交換して音を良くする考えよりも、ポールピースの高さを直した方が音を良くする意味では効果が上だと思います。

    状態も良くなり音も良くなったのでギターとして良いモデルに生まれ変わったと思います。

    ありがとうございました♪


    This is an Emotion Stratocaster with nut groove cut adjustment, fret grind, and pot replacement.

    The guitar is in bad condition with a clogged part. The frets are inevitably worn out if the guitar has been played a lot, so repairs are necessary.

    Replaced with Van Zandt Vintage Plus, and replaced the volume with a buzzing sound.

    The customer has retracted the third and sixth strings, resulting in a well-balanced sound.

    Single coil guitars still have a poor string volume balance, and because the makers are amateurs, many of them are still using the old specifications without noticing the anomaly.

    The volume balance of the strings is very important, especially since guitars are often played on chords. If the volume of the strings is not correct, the loud strings will be emphasized and the quiet strings will be hard to hear, resulting in a muted or sweet sound, and the chords will not sound beautiful.

    In my opinion, fixing the height of the pole piece is more effective in terms of improving the sound than replacing the PU to improve the sound.

    I think it has been reborn as a good model as a guitar since it is in better condition and sounds better.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240310212933
  • スクワイヤー日本製 Eシリアル ストラトキャスター フレットすり合わせ

  • 2024/08/16
  • Category:
  • スクワイヤー製ストラトキャスターのフレットすり合わせです。

    Eシリアルの国産時期のモデルです。

    フレット状態が悪く音詰まり箇所・チョーキングで音詰まり、ハイ起き気味でかなり状態が悪いです。
    ただ年代を考えたらこれ位の状態が普通です。
    古い年代=状態が悪い事が当然なので、中古で購入する際には状態に期待しない方が良いです。

    古い年代は80~90年代でも高額で売れる様になり、状態等は平気でウソを付いて販売する所も多いです。
    楽器店や楽器業者も素人が多いので、ウソを付いてなくても状態等の判断ができない人が売っている事も多いので要注意です。

    フレットをすり合わせ問題が無い状態に仕上げる事ができました。

    ありがとうございました♪


    This is a Squier Stratocaster fret grinder.

    This is a domestic period model with E serial.

    The frets are not in good condition, and the sound is stuck at the choking point and high up.
    However, considering the age of the guitar, this level of condition is normal.
    It is natural that old age = poor condition, so when you buy a used one, you should not expect it to be in good condition.

    Older instruments can be sold for high prices even in the 80s and 90s, and there are many places that sell them lying about their condition and so on.
    Since many music stores and musical instrument dealers are also amateurs, even if they are not lying, there are many people who cannot judge the condition of the instruments they sell, so be careful.

    We were able to finish the fretboard without any problems.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20230928202716
  • FenderJAPAN ストラトキャスター フレットすり合わせ&ナット溝切り調整&ポット交換

  • 2024/08/15
  • Category:
  • フェンダージャパン製ストラトキャスターのフレットすり合わせ・ナット溝切り調整・ポット交換です。

    Vo不良で音が安定して出ない状態、フレット消耗で音詰まり、11-48弦を張っててナット溝に弦が合わずナット高が高い状態です。

    またアームバーのビス山が痛んでいるのか非常に動きが硬い状態、ビス山が壊れて破片が挟まっていた様子です。

    ストラトはボリュームを可変させて使用する事も多いと思うので消耗し易い所です。新品に交換し解決しました。

    ナットは大体1~2ゲージが入る様に切っている場合もあれば張った弦に合わせてキチキチに切る場合とメーカーの匙加減が異なります。
    ギターの場合10-46か09-42と幅広くゲージが使われる事が多いので、私は09を張る場合でも後から10に変更しても問題が無い様に46が入る様に溝を切っていた方が良いと考えます。それ以上のゲージは意図して使う事が多いので変更等は考えず張った弦に合わせて切ります。

    フレットをすり合わせ、弦に合わせて溝を切りまともに使用できる状態に修正しました。

    ありがとうございました♪


    This is a Fender Japan Stratocaster fret grind, nut groove cut adjustment, and pot replacement.

    The sound is not stable due to Vo failure, fret wear and clogging, and the nut height is too high due to the 11-48 strings not matching the nut groove.

    The arm bar screws are damaged and the movement of the arm bar is very stiff, and it looks like the screw threads were broken and debris was caught in them.

    The arm bar is easily worn out because strats are often used with variable volume. We replaced it with a new one and solved the problem.

    The nut may be cut to fit 1 or 2 gauge strings, or it may be cut too tight to fit the strings you have put on it.
    In the case of guitars, I also think that it is better to cut a groove so that 46 can fit even if you put on 09 so that there will be no problem if you change to 10 later. Gauges higher than this are often used as intended, so we cut the grooves to match the strings that have been strung without thinking about any changes.

    The frets have been grated and the grooves have been cut to match the strings, and the fretboard is now ready for proper use.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240402203159
  • t.m.p ストラトキャスター PU交換&ジャック交換&セットアップ GRINNING DOG

  • 2024/08/13
  • Category:
  • IMG20240402184115

    t.m.p製ストラトキャスターのPU交換・ジャック交換・セットアップです。

    グリニングドッグ製55年モデルPUに交換、ジャックが消耗で交換しました。

    ギター本体もPUも知る人ぞ知るメーカーです。

    交換後のサウンドは耳に痛い所が出なくてコンプ感がありますが巻き弦の丸い感じの音が良いです。
    プレーン弦の音も痛くないのでストラト的にはマイルドなサウンドになります。
    巻き弦がトレブリーにうるさくないので細い音に感じない点も好印象です。

    PUの良さを引き出すのも本体の良さが必要なので、良いPUを買う事も大事ですが本体の良さも大事です。
    PUだけで音が決まっていると思っている人が多い印象ですが、大事な所はあくまでギター本体です。

    ありがとうございました♪


    This is a PU replacement, jack replacement and setup for a t.m.p Stratocaster.

    Replaced with a ’55 model PU made by Grinning Dog, jack replaced due to wear and tear.

    The guitar itself and the PU are both made by a well-known manufacturer.

    The sound after the replacement is not painful to the ear and has a comped feel but has a nice rounded sound of the wound strings.
    The sound of the plain strings is also not painful, so it sounds mildly Strat-like.
    I also like the fact that the wound strings are not too loud on the treble so it does not feel like a thin sound.

    It is important to buy a good PU, but it is also important to have a good body.
    I have the impression that many people think that the sound is determined by the PU alone, but the important part is the body of the guitar.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240306213012
  • レジェンド ストラトキャスター 配線直し&セットアップ

  • 2024/08/04
  • Category:
  • レジェンド製ストラトキャスターの配線直し・セットアップです。

    お客様の方で配線改造をして失敗した状態です。

    配線をやり直し無事に音が出ました。

    調整してみると意外と音が良く弾き易い個体で、3000円で買った個体との事です。
    元々は低価格帯ですが近年は精度も良くなってまず大きな不具合は減ったと思います。

    昔は1万円程度だとフォトジェニック製等のイメージが強く、誰がどう見ても酷かった物が多い代表メーカーですが近年はそうした酷い物も少なくなっています。

    ありがとうございました♪


    This is a rewiring and setup of a Legend Stratocaster.

    The customer had made some modifications to the wiring and it failed.

    The wiring was rewired and the sound came out fine.

    The sound is surprisingly good and easy to play.
    The price was originally in the low price range, but the accuracy has improved in recent years, and I think the number of major problems has decreased.

    In the past, when the price was around 10,000 yen, there was a strong image of photojournalistic products, etc., and there were many representative manufacturers whose products were terrible by all accounts, but in recent years, such terrible products have become less common.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240225203007
  • FenderJAPAN Fシリアル ストラトキャスター ナット溝切り調整&フレットすり合わせ&ポット交換

  • 2024/07/29
  • Category:
  • フェンダージャパン、Fシリアルのストラトキャスターのナット溝切り調整・フレットすり合わせ・ポット交換です。

    ボリュームにガリ、フレットの消耗、ナット高が高い所がある状態です。
    当時でも低価格帯になりますので細かい点は完璧ではありません。
    現行品のフェンダー製品でも高額なモデルでもナットの高さが各弦で異常に上下がある物も多くあります。

    パーツを交換しフレットをすり合わせ、ナット溝を仕上げる事で弾き易く問題が無い状態に仕上がりました。

    またトラスロッドの余り量が多く、ネック強度が高いです。
    昔は「良い木材があった」と分かる状態ですね。長い年月を生きてきてこの消耗状態で判断するなら木材が良い証拠です。
    この年代ですらヴィンテージ扱いされて非常に高価になっている事は疑問なのですが、現代と比べて明らかに木材の質が違うのは確かです。

    昔は低価格帯でも今で比較する所で30~40万円クラスの木材が数万円で使用されていた時代です。
    なので当時のフェンダージャパン製はコストパフォーマンスが良く、別に昔の物でなくても2000年代中期辺りまでの物でも非常に良い物が多いです。

    はっきり言えばこの年代を考えれば「数万円で良い楽器は普通にあった」となります。
    と言っても昔からビジネス洗脳は強いので誰も特別な見向きはしなかった事でしょう。
    今の高額な現行モデルよりも当時のフェンダージャパン製の方が音が良い場合が多いです。

    ありがとうございました♪


    This is a Fender Japan, F-Serial Stratocaster with nut groove cut adjustment, fret grind and pot replacement.

    It is in good condition with some galling on the volume, fret wear, and high nut height in some places.
    It is in the low price range even at the time, so the details are not perfect.
    Even with current Fender products, there are many high priced models where the nut height is abnormally high or low on each string.

    By replacing the parts, adjusting the frets, and finishing the nut groove, the guitar is now easy to play and has no problems.

    Also, there is a lot of truss rod left over and the neck is very strong.
    You can tell that there used to be “good wood” in this condition. If you judge by this worn condition after living for many years, it is a proof that the wood is good.
    I doubt that even this age is treated as vintage and very expensive, but the quality of the wood is clearly different compared to today.

    In the old days, even in the low price range, wood of 300,000-400,000 yen class was used for tens of thousands of yen in comparison with today.
    Therefore, Fender Japan-made guitars of that time had good cost performance, and even if they were not made in the old days, there were many very good ones until around the mid-2000s.

    To put it bluntly, considering this period, “good instruments were usually available for tens of thousands of yen”.
    However, business brainwashing has been strong for a long time, so no one would have paid special attention to them.
    In many cases, Fender Japan-made instruments back then sounded better than today’s expensive current models.

    Thank you very much♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240329211724
  • Tokai ストラトキャスター ナット交換&フレットすり合わせ

  • 2024/07/21
  • Category:
  • トーカイ製ストラトキャスターのナット交換・フレットすり合わせです。

    古い年代製になります。そうした個体は基本状態が悪い為、中古で購入された際は大掛かりなリペアが必要になる事があります。

    ナットは音詰まり、フレット状態も悪いです。

    ナットを交換しフレットをすり合わせる事で状態を良くし問題無い状態に仕上げました。

    ジャパンビンテージと言われる年代も確かに今の現行品と比べると音の面で良い個体が多いのは事実ですが、それに伴い状態が悪く許容内か許容外かで扱いが変わってきます。

    基本的に古い物は状態が悪く、特にトラスロッドに余裕が無いと上手く直せない原因となりますので購入前に絶対に確認しておきたい重要ポイントです。

    ありがとうございました♪


    This is a Tokai Stratocaster with nut replacement and fret grind.

    This is an older model. The nut is clogged and the frets are in bad condition.

    The nut is clogged and the frets are in poor condition.

    The nut has been replaced and the frets have been fretted to improve the condition of the fretboard.

    It is a fact that many of the vintage Japan vintage guitars have better sound than the current ones, but the condition of the vintage guitars may vary depending on whether they are in acceptable or unacceptable condition.

    Basically, older ones are in poor condition, especially if there is no room in the truss rod, which can be the cause of not being able to fix it well, so it is definitely an important point to check before purchasing.

    Thank you very much… ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE