タグ別アーカイブ: Ibanez

    PXL_20250315_083839319
  • Ibanez RG460DX-ROM Roadster Orange Metallic RG セットアップ

  • 2025/05/11
  • Category:
  • アイバニーズ製RG460DXのセットアップです。

    新品で購入したが音詰まり箇所があり調整に持ち込まれました。

    状態を確認すると4フレットで音詰まりが発生しており、5フレットだけ高い状態で4フレットが音詰まりする状態です。

    新品でもこうした不具合があるまま平気で販売されている事があるので、購入前に店員にチェックさせて買うのは当然ですがお店側が素人だと不具合に気が付きません。

    酷いお店だと初期状態の弦高が高く、弦高を高くすれば不具合箇所が誤魔化されるので音詰まりが分かり難くなります。
    なので弦高が高い時点で疑った方が良いです。
    購入後に指摘しても「当店での基準はこの弦高で不具合が出なければ問題無いと判断してます。」と誤魔化されて終わりです。

    不具合箇所が分かれば新品なら1年保証等が付いているので、基本は早い方が良いですが不具合を発見した際は購入店に申し出て直してもらいましょう。

    ただし相手が素人過ぎるとこうした圧倒的に誰でも分かる不具合ですら店員が不具合を分からない現象が起きて対応してくれない事が出てきます。
    実際にこの個体はリピーターのお客様のギターの為、後日に別のギター持ち込み時にお客様からこのギターは初期不良で返品した報告を聞いた際の購入した楽器店のやり取り話を聞きました。

    この音詰まりする状態でも楽器店側は「メーカーが送ってきた状態なので、状態は基準の範囲で問題無い」との事や「他リペアショップでチェックさせても構わない」とまで言われたそうです。
    ちなみにギター本体はお店に送ってあり店員が確認した状態での連絡です。そのやり取りメールも確認しました。

    私のお店でチェックした事はお客様が購入店に伝えてなかったそうですが、楽器店側の素人さがここまで来てると買うのが危険なレベルになっています。
    この個体はそこまで高額なモデルではありませんが、万が一高額なモデルを購入してアフターサービスがここまで酷いと楽器は楽器屋で買う事が難しくなってきます。

    楽器屋で買う際も基本的に知ってほしい知識としてちゃんと調整した上で渡してもらう事、トラスロッドの余り量を確認させる事、そもそも新品でトラスロッドの余り量を表示しないなら買わない事、不具合が起こった場合はどの様な対応をするのか必ず確認する事です。

    今回は何度もメールのやり取りの上でやっと返品できたレベルとの事で、明らか商品に不具合があるのに返品する事すら困難という事例をお客様から見せてもらいました。

    楽器屋をやってる人達へ向けて、もう少し自分の仕事にプライドを持って下さい。
    金儲けしか考えていないならこの仕事を辞めて下さい。業界として害悪な存在です。
    人が泣いて金を儲けてるなら仕事としてのやり方が完全に間違っています。
    良い仕事をして喜ばせた対価としてお金を稼いで下さい。

    ありがとうございました♪


    This is a setup for an Ibanez RG460DX.

    It was purchased new but brought in for adjustment due to a jammed part.

    The condition of the guitar was confirmed to be clogged at the 4th fret, with only the 5th fret being high and the 4th fret being clogged.

    It is natural to have the store staff check the guitar before buying it, but if the store is an amateur, they will not notice the problem.

    If the shop is not a good store, the initial string height will be high, and if the string height is high enough, the defect will be disguised, so it will be difficult to recognize the sound clogging.
    Therefore, it is better to be suspicious when the string height is high.
    If you point this out after purchase, you will be misled and end up saying, “Our standard is that if there is no problem at this string height, we judge that there is no problem. If you point out the problem after purchase, you will end up being misled.

    If you find a problem, it is better to report it to the store where you purchased the instrument and have it fixed.

    However, if the store is too much of an amateur, there may be a phenomenon that the store staff does not understand the problem, even if the problem is overwhelmingly obvious to anyone else, and they may not be able to fix it.
    In fact, this guitar belongs to a repeat customer, and I heard a story about an exchange at the music store where the customer brought in another guitar and later heard a report that this guitar had been returned due to initial defects.

    Even with this clogged condition, the music store said that the condition was within the standard range because it was sent by the manufacturer, and that they were even willing to let another repair store check it out.
    Incidentally, the guitar itself was sent to the store and the store staff checked it. I also confirmed the email exchange.

    I heard that the customer did not tell the store of purchase that he had checked it at my store, but the amateurishness on the part of the music store has reached such a level that it is dangerous to buy it.
    Although this unit is not that expensive model, if you buy an expensive model and the after-sales service is this bad, it will be difficult to buy a musical instrument at a music shop.

    When buying from a music shop, the basic things you need to know are that you should have the instrument adjusted properly, that you should check the amount of truss rod left, that you should not buy a new instrument if it does not show the amount of truss rod left, and that you should always check what they do in the event of a problem.

    In this case, the customer told us that he was able to return the instrument after many emails, and that he found it difficult to return the instrument even though the product was obviously defective.

    To those who are in the music store business, please have a little more pride in your work.
    If all you care about is making money, get out of the business. You are a detriment to the industry.
    If you are making money by making people cry, you are doing your job completely wrong.
    Please do a good job and make money in return for pleasing people.

    Thank you.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20250211_083319999
  • Ibanez AZ2204 セットアップ

  • 2025/04/27
  • Category:
  • アイバニーズ製AZ2204のセットアップです。

    大きな順反りで弦高が高い状態です。弾き難い状態でも楽器屋では普通に売っているので調整してもらってから試奏を申し込んだ方が良いです。

    調整してみると弾き易く音が良いモデルです。
    シングルが特に音が良いですね。

    Ibanez製は低価格帯でも弾き易く音質が良いモデルが多いですが2020年代からインドネシア製に品質が結構変わってきているので注意が必要です。
    新品でもこの個体の様に初期状態で調整がいい加減だったり音が詰まる様な状態の物も出てきているので購入時はチェックの上で購入しましょう。

    ありがとうございました♪


    This is an Ibanez AZ2204 setup.

    It has a large forward bow and high string height. Even though it is hard to play, it is usually sold at music stores, so it is better to have it adjusted before applying for a trial.

    After adjustment, the model is easy to play and has a good sound.
    The singles sound especially good.

    Ibanez has many models in the low price range that are easy to play and have good sound quality, but be aware that the quality has changed quite a bit since the 2020’s to Indonesian made.
    Even new models, like this one, are sometimes in a poor state of initial adjustment or have a stuck sound, so check before you buy.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241223202057
  • Ibanez GB-10 ナット交換&フレットすり合わせ&ポット交換

  • 2025/04/03
  • Category:
  • アイバニーズ製GB-10のナット交換・フレットすり合わせ・ポット交換です。

    各所の消耗が大きく状態が悪いです。

    ナットで音詰まり箇所、フレット減りで音詰まり箇所がある状態です。
    ポットは固着で回らない所があります。

    内部をチェックすると古い年代製でトグルスイッチが特殊な構造で、しかも大きな穴に丸いゴム板に固定された特殊な構造で交換できるトグルが無くトグルスイッチ以外は交換する事となりました。
    一応はミニスイッチタイプのトグルは高さがあり使えますがノブの色が異なってきます。お客様と相談の上、そのままとなりました。

    ナットを交換しフレットすり合わせを行う事で問題無く弾ける状態になりました。

    固着したポット等も新品に交換し問題無く使用できる事となりました。

    ありがとうございました♪


    This is an Ibanez GB-10 nut replacement, fret grind and pot replacement.

    It is in poor condition with significant wear and tear in various areas.

    The nut is stuck and the frets are worn out.
    The pots are sticking and not turning in some places.

    The toggle switch is of a special construction, and there are no toggles that can be replaced, so we had to replace all but the toggle switch.
    The mini-switch type toggles are tall enough to be used, but the color of the knobs will be different. After consultation with the customer, we decided to leave it as it was.

    The nut was replaced and the frets were adjusted to fit the fretboard, so the instrument can now be played without any problems.

    The sticking pots and other parts were replaced with new ones, and the instrument can now be used without any problems.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241007212342
  • Ibanez JS3CR Joe Satriani Signature Model “Chrome-Boy” フレットすり合わせ&フレットサイド処理

  • 2025/02/09
  • Category:
  • アイバニーズ製JS3CRのフレットすり合わせ・フレットサイド処理です。

    サトリアーニモデルですね。

    基本的に現行品、製品という物はちゃんとできておりません。

    理由はコストの問題で1本1本を丁寧に作るには時間の都合上無理になる事と人件費が高騰するので、基本的に低価格帯では実現は不可能になります。

    高額な物でもそこまで基準が高いメーカーも少ないので、特にこの辺りが分かり易く出てくるのがナット・フレットになります。

    フレットサイド処理は仕上がりが良い物=高額な物となりますが、メーカーによっては50~60万円になっても微妙なメーカーも多くあります。
    フレットも丸め具合や精度も高い事が少ないので、ちゃんと使用したいなら買ったらすり合わせ・ナット溝切り調整が基本です。
    希望があればサイド処理も行った方が良いでしょう。

    フレットをすり合わせ、サイド処理を行う事で見違える位に弾き易くなりました。

    フレット関係は元が酷いと直した際に驚く様な良い状態になるのでお勧めです。

    ありがとうございました♪


    This is an Ibanez JS3CR fret mortise and fret side treatment.

    This is Satriani model.

    Basically, current products are not made properly.

    The reason is that it is impossible to make each one of them carefully due to the cost problem, and the labor cost is soaring, so it is basically impossible to make them in the low price range.

    There are few makers who have such high standards even for high-priced instruments, so the nut and fretboard are the most obvious examples of this.

    For the fret side treatment, a good finish means a high price, but depending on the maker, there are many makers who can make a fret side treatment for 500,000-600,000 yen, but it may be too subtle.
    The fret is rarely rounded well and accurate, so if you want to use it properly, you need to adjust the fret and nut groove if you buy it.
    If you want to use it properly, you should also do side treatment if you wish.

    The fret fret adjustment and side treatment made it easier to play.

    If the original fretting is not good, you will be surprised how good it will be when it is repaired.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241117183754
  • Ibanez QX527PB 配線直し&セットアップ ローステッドメイプル

  • 2025/01/28
  • Category:
  • アイバニーズ製QX527PBの配線直し・セットアップです。

    トラスロッドに余裕が殆ど無い状態で弾き難い状態、調整でトラスロッド限界になりましたがそれでもやや順反り状態です。

    配線が非常に雑でセレクターの配線が間違っている+セレクターが壊れ掛けている状態です。
    素人いじりされている状態で恐らく前オーナーが直せず手放した物と思われます。

    このモデルはボディが薄い為、背の低いセレクターじゃないと付かないボディ厚です。
    主に安物セレクターしか付きません。

    また他にもコンデンサの数値が間違っておりトーンが全然効かないのを交換しトーンが効く様になりました。

    中古品の購入は正直こうした事が多いので、基本的に見えない所は難があると思ってた方が良いです。

    ありがとうございました♪


    This is an Ibanez QX527PB rewired and setup.

    The truss rod was adjusted to the limit of the truss rod, but it is still slightly bowed.

    The wiring is very messy and the selector is wired incorrectly + the selector is almost broken.
    It is believed to have been tinkered with by an amateur and probably given away by the previous owner who was unable to fix it.

    The body of this model is so thin that only a short selector can be attached to it.
    Only cheap selectors can be attached to this model.

    The capacitor was not working properly, but I replaced it and now the tone works.

    I have to admit that this is what happens when you buy used equipment, so basically you should assume that there is something wrong with the parts that you can’t see.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20241026195317
  • Ibanez SR405EPBDX-TSU SR セットアップ

  • 2025/01/21
  • Category:
  • アイバニーズ製SR405のセットアップです。

    大きく順反りし弾き難い状態です。

    アイバニーズ製の低価格帯もちゃんと調整さえすれば弾き易く音も良いのですが、新品でも個体差により長持ちが期待できない物も多く存在します。
    こればかりは近年の木材が柔らか過ぎなので、その辺りも考えて物を買わないと完全に短期間の消耗品となってしまいます。

    調整後はトラスロッドに余裕が殆ど無い状態になりました。
    5弦ベースは張力が強いので基本的にトラスロッドの余り量は少なくなる傾向になります。

    張力が強いので弦を張るだけで大きく順反りします。
    そこをトラスロッドで調整するので多く回す必要があり、木材が柔らかいとその分大きく順反りします。
    酷い場合はネック自体は真っ直ぐだが弦を張ると大きく順反りする→トラスロッドを限界まで回してやっと真っ直ぐに調整できる物も多くなってきました。
    リペアマンでもバカが多いですが、弦を張りっぱなしで良いとか言ってる人は避けて下さい。
    現実を知らな過ぎか、間違った情報を教えて客に楽器を壊させて買い替えや修理で儲ける事しか考えていません。

    5弦ベースを購入するなら補強材が入っている物を買うと長持ちし易いです。
    当たり前ですが買う際にトラスロッドの余り量を必ず確認して下さい。
    5弦ベースに限らず新品初期状態で「トラスロッドの余り量が少ない=木材が柔らかく長持ちさせるには不向き」と考えて間違いありません。

    音が良く弾き易いモデルです。
    トラスロッドの余り量的に安心して使用し続けられる状態ではありませんが弦は緩めて保管する・加湿を行い乾燥させない様にする事でこれ以上反らない様にする努力が必要です。

    ありがとうございました♪


    This is an Ibanez SR405 setup.

    It is hard to play because of the large forward bow.

    Ibanez low-priced guitars are easy to play and sound good as long as they are properly adjusted, but there are many new guitars that cannot be expected to last long due to individual differences.
    However, there are many new instruments that cannot be expected to last for a long time due to individual differences.

    After the adjustment, there is almost no room left in the truss rod.
    The truss rod has little room to spare because of the high tension of a 5-string bass.

    Since the tension is so strong, just by stretching the strings, a large amount of forward bending will occur.
    The truss rod must be turned a lot to adjust the tension, and if the wood is soft, this will cause a large amount of forward bowing.
    In the worst case, the neck itself is straight, but when the strings are stretched, the neck warps greatly, and many of them can only be adjusted straight by turning the truss rod to the limit.
    There are many repairmen who are idiots, but please avoid those who say that it is OK to leave the strings on.
    They are either too ignorant of reality, or they only think about making money by giving wrong information and making customers break their instruments to buy replacements or repairs.

    If you buy a 5-string bass, buy one with reinforcement so it will last longer.
    Of course, you should always check the amount of truss rod left when you buy a bass.
    Not only 5-string basses, but you can be sure that “a small amount of truss rod left over” in the initial state of a new bass means that the wood is soft and not suitable for a long life.

    This model has a good sound and is easy to play.
    The amount of truss rod left is not enough to keep it in good condition, but you need to make an effort to keep it from warping any further by keeping the strings loose and humidifying it to prevent it from drying out.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240722185446
  • Ibanez Axion Label RG631ALF ナット溝切り調整&セットアップ&配線直し

  • 2024/11/26
  • Category:
  • アイバニーズ製アクシオンレーベルのナット溝切り調整・セットアップ・配線直しです。

    11-56弦でドロップC仕様に変更と、付いているフィッシュマンPUにコイルタップ配線、ON-OFF-ONを使用しコイルタップ(インサイド・アウトサイド)改造の内容です。
    配線は相談の上ネットで調べて出てきた配線にて行う形となりました。
    またトーンにスイッチポットを増設しボイス2へ切り替え機能を移動(元はスイッチで行えたのを今回のスイッチポットに移動)しました。
    元のスイッチ箇所には増設したコイルタップ機能となります。

    フィッシュマンPUはコイルタップを増設すると音色のバリエーションが増えるので使用用途がしっかりしていれば活用できます。
    PUのイン・アウトの場所違いコイルタップも正直大きな差はありませんが音が柔らかい・硬いのニュアンスになります。
    変化として大きくはありませんがフィッシュマンで出力を押さえたサウンドが出せるので意外と思っていたよりも良いコイルタップ音です。

    ありがとうございました♪


    This is a nut groove cut adjustment, setup and rewiring of an Ibanez Axiom Label.

    The wiring was changed to 11-56 strings with drop C specs, coil tap wiring for the attached Fishman PU, and coil tap (inside/outside) modification using ON-OFF-ON.
    The wiring was done after consulting with the owner and using wiring found on the internet.
    A switch pot was added to the tone and the switching function was moved to voice 2 (originally done with a switch, but now moved to this switch pot).
    The original switch pot now has a coil tap function.

    The Fishman PU can be used for a wider variety of tones by adding coil taps, so if the intended use of the PU is solid, it can be utilized.
    To be honest, there is not a big difference between the in/out PU location and the coil tap, but the sound will be softer or harder.
    It is not a big change, but it is a surprisingly better coil tap sound than I expected because I can get a sound with the output held down by the Fishman.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240705185514
  • Ibanez 1980 AR100 Artist -CS セットアップ&配線直し

  • 2024/11/12
  • Category:
  • アイバニーズ製AR100のセットアップ・配線直しです。

    音がまともに出ない状態です。
    古い年代製である事から電装系は使い物にならない状態です。
    電装系を全て交換しました。

    トラスロッドの余裕が少ないですがまだまだ使用できる状態です。
    PUのポールピースが固着で回らない箇所がありました。

    パワーが大きいPUで見た目よりも歪み寄りに特化したギターです。

    ありがとうございました♪


    This is a setup and rewiring of an Ibanez AR100.

    The sound does not come out properly.
    The electrical system is unusable due to the old age of the instrument.
    All the electrical components have been replaced.

    The truss rod has a little room, but it is still usable.
    The pole piece of the PU is stuck and cannot be rotated.

    The PU has a lot of power and is more specialized for distortion than it looks.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240608174604
  • Ibanez Q547 ナット溝切り調整&セットアップ ローステッドメイプル

  • 2024/10/01
  • Category:
  • アイバニーズ製Q547のナット溝切り調整・セットアップです。

    新品ですがナット高が高くかなり弾き難い状態です。

    ナット溝を削り適切な高さにする事で弾き易くなりました。

    また最初から殆どトラスロッドに余裕が無い状態で実質限界状態で売られていました(45°位しか回せなかった)。
    「ローステッドメイプルだから反らない」というオカルトを信じている人も多いのですが、この様に普通に反ります。
    調整でトラスロッドが限界状態となりました。

    こうした物も平気で売られている事も多いので珍しい話ではありませんが、この辺りを公表せず平気で売っている事実は知っておいた方が良いです。
    近年の木材は柔らかく、弦を張ると大きく順反りするのでまずその調整にトラスロッドが多く回されます。
    そうした強度が無いネックは弦張力に負けて順反りするので、それを直すと新品で既にトラスロッドに余裕が無い状態で販売される簡単な話です。

    この状態で販売されている訳ですから、当然弦を張りっぱなしにしていたらどうなるか?簡単に分かると思います。
    多くのネット情報で「弦は張りっぱなしでも良い」と言われているのは買った人に「自分の責任で楽器をダメにさせて買い替えさせたいから」です。
    まず簡単にまともな楽器屋・リペアマンか判断できる方法として「弦を張りっぱなしで良い」という所は避けましょう。

    ありがとうございました♪


    This is a nut groove adjustment and setup for an Ibanez Q547.

    Although new, the nut height is high and it is quite difficult to play.

    By cutting the nut groove to the proper height, it became easier to play.

    Also, the truss rod was sold with almost no room at all from the beginning (it could only be turned about 45 degrees).
    Many people believe in the occult that “roasted maple doesn’t warp,” but it usually does.
    The truss rod was at its limit after adjustment.

    It is not uncommon to find such items sold without any problem, but you should be aware of the fact that they are sold without any problem without disclosing this.
    Recent wood is soft and warps greatly when strings are stretched, so the truss rod is often used to adjust it.
    If the neck is not strong enough to handle the tension of the strings, it will warp forward, so it is easy to sell a new neck with no room in the truss rod.

    Since the neck is sold in this condition, it is easy to understand what would happen if the strings were left on the neck. It is easy to see.
    The reason why so many people on the Internet say that it is OK to leave the strings on is because they want the buyer to ruin the instrument and replace it at his/her own risk.
    First of all, as an easy way to judge if the shop is a decent music shop/repairman, avoid places that say “you can leave the strings on”.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240606174826
  • Ibanez FR800 セットアップ

  • 2024/09/30
  • Category:
  • アイバニーズ製FR800のセットアップです。

    日本未発売モデルとの事です。
    近年はこうした日本には販売されていないモデルを逆輸入して使用する人も居られますね。

    ベアナックルの様なオリジナルPUが付いており、ハイゲインでなく音の芯が強く分離が良いのでクリーンも歪み等もバランス良くてかなり良いPUが標準搭載の様です。

    近年は日本市場を考えていない様な話もあり、それだけ日本では利益にならない判断がされている話もあります。

    本当に良い物を選んで購入しないと、良いメーカーが離れていってしまいます。

    購入者側が正しく買い物ができるか?も重要な要素です。

    ありがとうございました♪


    This is an Ibanez FR800 setup.

    This is a model that has not been released in Japan.
    In recent years, there are people who reimport these models that are not sold in Japan and use them.

    It has an original PU like Bare Knuckle, which is not high-gain but has a strong sound core and good separation, so it seems to have a good balance of clean and distorted sounds.

    In recent years, there is a story that they are not considering the Japanese market, and there is a story that they are making decisions that are not profitable in Japan.

    If you don’t select and purchase really good products, good manufacturers will leave you.

    Can the buyer shop correctly? is also an important factor.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE