年別アーカイブ: 2024年

    IMG20240710215530
  • Gibson SG セットアップ

  • 2024/11/03
  • Category:
  • ギブソン製SGのセットアップです。

    順反りして弾き難い状態、ややハイ起き気味の状態です。

    音詰まりする箇所はあるがまだ何とか使用できるレベルです。

    トラスロッドの余り量も多く状態としては良好ですが各所の状態があまり良くないのですり合わせ等で対処した方が良い状態です。

    ナット高が消耗で詰まる寸前まで消耗していたりと、いずればフレットもすり合わせ・ナット交換された方が良い状態です。

    ありがとうございました♪


    This is a Gibson SG setup.

    It is in a forward warped, hard to play condition, and a little high up.

    There are some parts where the sound is clogged, but it is still usable.

    The truss rod is in good condition with a lot of excess, but the condition of various parts is not so good that it would be better to adjust the truss rod by rubbing.

    The nut height is almost worn out to the point of jamming, and the fret board should be replaced.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    IMG20240717214556
  • Jackson Pro Series Dinky DK Modern フレットすり合わせ&PU交換

  • 2024/11/01
  • Category:
  • ジャクソン製プロシリーズのフレットすり合わせ・PU交換です。

    フレット消耗が大きい状態です。

    お客様持ち込みの中古で入手したPU、セイモアダンカンSH-2・13に交換です。

    中古でパーツを買う際の注意点ですが、元の状態と異なる可能性があります。
    PUはエスカッションに取り付けるか直付けか?でビス穴に加工がされています。
    その他にも前オーナーの素人作業により破損が起きている等も考えられます。

    SH-13は取り付けビス部分がヒビ割れしており、簡単に割れたのでそのままでは取り付けできない状態になっておりました。
    恐らくこれらが理由で前オーナーが破損個所を隠して販売した物と思われます。
    割れ箇所を接着剤で補強&接着を行って取り付けました。

    ジャクソンやシャーベル等は地味に音が良く弾き易いモデルが多いのでお勧めです。
    やはり一般的で無い様なメーカーには良い物が多いので、メタルギターのイメージが強いかもしれませんが結構万能的なモデルです。

    ありがとうございました♪


    This is a Jackson Pro Series fret grind and PU replacement.

    The fret wear is significant.

    This is a replacement for a Seymour Duncan SH-2/13 PU, which was obtained used and brought in by the customer.

    Please note that when buying used parts, there is a possibility that they may differ from the original condition.
    Is the PU attached to the escutcheon or directly? The screw holes have been modified with
    There are also other possibilities such as damage caused by the previous owner’s amateur work.

    The SH-13 has a cracked mounting screw, and since it cracked easily, it could not be installed as it was.
    We believe that the previous owner concealed the damaged parts and sold it for these reasons.
    We reinforced and glued the cracked parts with adhesive and installed them.

    We recommend Jackson and Charvel because they are easy to play and have good sound.
    There are many good products from uncommon makers, so although they may have a strong image of metal guitars, they are quite versatile models.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240714203828
  • Shijie ストラトキャスター セットアップ STE-V CUSTOM

  • 2024/10/31
  • Category:
  • シージェ製ストラトキャスターのセットアップです。

    中国のハイエンドギターブランドとの事です。

    初めて触りましたが作りが良く弾き易い、ワーモスを組んだかの様な仕様ですが値段が安過ぎです。

    値段を考えたら非常に高いコストパフォーマンスですので、日本に流通してくると他メーカーも中々無視できない存在になってくると思います。

    高額なのに質が低いメーカーが増えてきましたが、今後ブランドだけで物を売るのは厳しくなってくると思います。

    ありがとうございました♪


    This is a Stratocaster setup made by Sije.

    It is a high-end guitar brand from China.

    I touched it for the first time, and it is well made, easy to play, and has specifications as if it were assembled from Warmoth, but the price is too low.

    Considering the price, the cost performance is very high, so I think other makers will not be able to ignore it when it is distributed in Japan.

    I believe that it will become tougher to sell products only by brand in the future, although the number of expensive but low quality manufacturers is increasing.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240630185053
  • Edwards KingV 配線直し

  • 2024/10/30
  • Category:
  • エドワーズ製キングVの配線直しです。

    確認してみると配線が間違っている状態です。

    ジャックがガリにより交換、ポットも交換しました。
    配線の間違いを直す事で問題無い状態へ修正しました。

    音が良く歪みのノリも良いモデルです。
    意外と変形ギターで弾き難いだけで音は良かったりする事もあります。
    フライングV等も弾いてみると音が良かったりする事も多いので、弾いて確認してみないと分からないものです。

    ありがとうございました♪


    This is a rewiring of an Edwards King V.

    Checked and found that the wiring is incorrect.

    The jack has been replaced due to galling, and the pot has also been replaced.
    By fixing the wiring error, it was corrected to the condition where there is no problem.

    This model has a good sound and good distortion.
    It is surprising that sometimes a deformed guitar is hard to play but the sound is good.
    Flying V and other guitars often sound good when you play them, so you never know unless you play them and check them out.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240722171057
  • Tayer 214CE セットアップ

  • 2024/10/29
  • Category:
  • テイラー製214CEのセットアップです。

    大きく順反りし弾き難い状態です。調整でトラスロッドが限界状態となりました。

    テイラー製はアコギメーカーの中でも弦高が低く弾き易い部類です。

    ただ順反りしたりトップ浮きも発生してくると弾き難い事は他と変わりません。

    またメーカー自体も弦を張りっぱなしで良いとされているメーカーですが、この様に状態が悪くなるのならメーカーが保証すべき所でしょう。
    基本的に張りっぱなしで良いとするなら弦張力に十分に負けない位のネック強度が必要ですが、弦をチューニングしてみて分かると思いますがチューニングしている段階で緩む(順反りする)事から既に張力に負けていると分かるはずです。
    弦張力に負けている状態を続けていればどうなるか?簡単な話です。

    弦は緩めて保管しないといけません。アコギはネック反りの他にトップ浮き(弦高が高くなる)も発生するので尚更張りっぱなしで良い訳がありません。
    具体的にはトラスロッドの余り量を把握する、状態を把握した上で考えないといけません。

    どちらにしても大手が間違った情報を出している現実を知る事、自分で学んで実践していかないと楽器を自分でダメにしてしまいます。

    ありがとうございました♪


    This is a Tyler 214CE setup.

    It is hard to play due to the large forward bow. The truss rod has been adjusted to the limit.

    Tyler 214CE is one of the easiest acoustic guitars to play because of its low string height.

    However, if the strings are warped and the top is floating, it will be difficult to play.

    The manufacturer itself also says that it is fine to leave the strings in place, but if the condition deteriorates like this, the manufacturer should guarantee that it will be fine.
    Basically, if you want to leave the strings in place, the neck must be strong enough to withstand the tension of the strings, but as you can see when you tune the strings, you can already tell that the strings are losing tension because they loosen (warp in the forward direction) when tuned.
    What happens if the string continues to lose tension? It is simple.

    The strings must be kept loose. In addition to neck warp, acoustic guitars also suffer from top lift (higher string height), so there is no reason to leave the strings taut.
    In particular, you need to know how much truss rod is left, and you need to know the condition of the truss rod before you think about it.

    In any case, it is important to know the reality that the major companies are giving wrong information, and if you don’t learn and practice by yourself, you will ruin your instrument by yourself.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240726204838
  • G&L SB-2 フレット部分すり合わせ&セットアップ

  • 2024/10/28
  • Category:
  • G&L製SB-2のフレット部分すり合わせ・セットアップです。

    中古品ですが購入前に楽器店で細かく詳細を確認して購入したとの事ですが状態がかなり悪いです。
    大きく順反りして弾き難い・1弦だけやたら弦高が高く弾き難いです。
    こうした悪質な売り方をしている所はたくさんある事や、または状態を判断できない素人店員が売っている楽器屋も非常に多いので信用できる所の方が少ないです。

    詳しくチェックしてみるとトラスロッドに余裕が殆ど無い状態です。
    楽器店でその場でトラスロッドを回させて確認したが問題無いと言われたそうですが、それもまた悪質ですね。

    楽器屋でトラスロッドを回させても「左右に回ります」等と誤魔化した言い方をしたら要注意です。
    左右に回るのは当たり前です。余り量がどれだけあるのか?と聞いているのにそれを答えられないのは都合が悪いからか素人なだけです。
    トラスロッド限界近くで左右に回るのか?とトラスロッドがユルユルな位に余ってて左右に回るのか?でも状態が全然違います。
    正しく答えないのは「売るのに都合が悪いから」です。

    フレット浮きにより音詰まり箇所がありますが、その辺りの説明も無かった様子です。
    1弦の音詰まり箇所も、何故か異常に1弦だけ弦高が高く調整されていた事もあり明らか状態を分かってて渡しております。

    音詰まりしているフレット浮き箇所のみ削って音詰まりが出ない状態にしました。

    本来なら返品すべき商品ですが、お客様の要望で対応しました。
    こうした内容が分かった際は大体買った所へ返品を勧めます。
    そうした事をたくさんしているから私は楽器屋の方から嫌われます。
    イベントに誘われない程度の被害でしかないですが、全く知らないリペアショップや個人楽器バイヤーにすら声が掛かるのに私には掛からない等を見せられると嫌味でしかありません。

    ありがとうございました♪


    This is a G&L SB-2 fret section mortise and set up.

    It is a used instrument, but the condition is quite bad, although the owner said he checked the details in detail at a music store before purchasing it.
    It is hard to play because of the large forward warp, and only the first string has a very high string height, making it hard to play.
    There are many places that sell these instruments in such a malicious manner, and there are also many music stores where amateur salesmen who cannot judge the condition of the instruments sell them, so there are few places you can trust.

    If you check the truss rod in detail, you will find that there is almost no room left in the truss rod.
    The music store had him turn the truss rod on the spot to check it, and he was told there was no problem, which is also malicious.

    Be careful if the music shop deceives you by telling you that the truss rod turns left and right.
    It is a matter of course that it turns left and right. How much of a truss rod is left over? If you cannot answer that question, it is either because it is inconvenient or you are just an amateur.
    Does it turn to the left or right near the limit of the truss rod? Or is the truss rod so loose that it turns from side to side? The condition is totally different depending on whether the truss rod is too loose to turn left or right.
    The reason I don’t answer correctly is because it is inconvenient to sell.

    There is a clogging point due to fret lift, but there seems to have been no explanation about that.
    The first string is also clogged, and for some reason, the height of the first string was adjusted abnormally high, so I gave it to him knowing the obvious condition.

    We shaved only the fretted part that was clogged and made it so that it was not clogged.

    The guitar should have been returned, but the customer requested us to do so.
    When I find out that something like this has happened, I usually recommend that the customer return the instrument to the place where he or she bought it.
    I do this a lot, which is why music stores don’t like me.
    I am only affected to the extent that I am not invited to events, but when I am approached by repair stores and even private instrument buyers that I don’t know at all and I am shown that I am not invited, etc., it is just sarcasm.

    Thank you.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    IMG20240809204426
  • Gibson Memphis ES-335 Block Export セットアップ

  • 2024/10/27
  • Category:
  • ギブソン製ES-335のセットアップです。

    2016年メンフィス製との事です。

    トラスロッドが殆ど余裕無し状態、調整でトラスロッド限界となりました。
    中古でも新品でもトラスロッドの余り量を確認して買わないと長い目を見たら損する事になります。

    トラスロッド限界状態ですが弾き易い状態にする事はできました。

    PUにMHSⅡが付いているとの事(楽器屋で購入時)で、音が良かったです。
    音だけは通常の335と違い特別感はありました。

    ありがとうございました♪


    This is a Gibson ES-335 setup.

    It was made in Memphis in 2016.

    The truss rod has almost no room, and the truss rod limit was reached by adjustment.
    If you don’t check the amount of truss rod left in a used or new guitar, you will lose money in the long run.

    Although the truss rod is at the limit, we were able to make it easy to play.

    I was told that the PU has MHS II (when I bought it at the music store), and the sound was good.
    Only the sound was different from a normal 335 and had a special feeling.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    IMG20240624182117
  • MOON オーダーベース セットアップ

  • 2024/10/25
  • Category:
  • ムーン製オーダーベースのセットアップです。

    現行の型番に存在しないモデルの様子です。

    ネック剛性があるのですがトラスロッドがあまり効かない状態です。
    ネック剛性が高過ぎる場合だとトラスロッドの力でネック反りがあまり動かない為、ネックが反った際の調整も不都合が起きます。

    順反りを直すのにトラスロッドが調整で限界となりました。

    太い弦を使用しており5弦はしっかりと鳴る状態でとても良いベースです。
    どうしても5弦ベースは張力が強いので、そもそも殆どのベースはトラスロッドの余裕が少ないです。

    弦を緩めて保管は当然として、乾燥させ順反りさせない努力も必要になります。
    状態を良く長年キープするにはいつもの事ですが保管努力が必要です。

    ありがとうございました♪


    This is a Moon made to order base setup.

    This is a look at a model that does not exist in the current model number.

    It has a rigid neck but the truss rod does not work very well.
    If the neck stiffness is too high, the truss rod will not be able to move the neck warp very much, so it will be inconvenient to adjust the neck when the neck warps.

    The truss rod has become the limit of adjustment to correct the forward warp.

    This is a very good bass with thick strings and the 5th string is in a solid sounding condition.
    Inevitably, 5-string basses have a lot of tension, so most basses have little room for the truss rod to begin with.

    It is natural to store the bass with the strings loosened, but it is also necessary to make an effort to dry it out and keep it from warping in order.
    As always, it takes a lot of effort to keep them in good condition for many years.

    Thank you very much.


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE