月別アーカイブ: 2026年5月

    PXL_20260228_083416970
  • PRS CE Custom24 配線直し

  • 2026/05/11
  • Category:
  • PRS CE製カスタム24の配線直しです。

    中古購入との事ですが音が出ない状態です。

    内部をチェックしてみると配線が間違っており、その上でセレクター不良でしたので交換し正しく配線して問題が無い状態に仕上げました。

    中古品もお店から買うのか個人から買うのでも違いはありますが、近年はお店で買っても中身をチェックせず問題無いと販売している所も増えてきております。
    実際は問題があるのに問題無いと売るショップがある事は知っておいて下さい。

    使用してて状態がおかしいな?と思ったら買った所よりもリペアショップに持ち込み下さい。
    どうしても楽器関係は労働環境が悪いので従業員の教育不良・まともな人が離れる傾向でどこも人手不足です。
    知識が無い人が多くなってきたので、そんな所でチェックした所で解決できない可能性が高いです。

    ありがとうございました♪


    This is a rewiring job for a PRS CE Custom 24.

    The customer purchased it used, but it wasn’t producing any sound.

    Upon inspecting the interior, I found that the wiring was incorrect, and the selector switch was faulty. I replaced the switch, rewired the guitar correctly, and restored it to full working order.

    There is a difference between buying used items from a store versus a private seller, but in recent years, even some stores have been selling items without checking their condition, claiming they are problem-free.
    Please be aware that there are shops that sell items claiming they are in good condition even when there are actually issues.

    If you notice something seems off while using it, please take it to a repair shop rather than the place where you bought it.
    The working conditions in the music instrument industry are notoriously poor, leading to inadequate employee training and a tendency for competent staff to leave, resulting in a shortage of personnel everywhere.
    Since there are more and more people without the necessary knowledge, there is a high probability that a check at such a place won’t resolve the issue.

    Thank you very much♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260221_083600328
  • FenderJAPAN Aシリアル ストラトキャスター セットアップ&ジャック交換

  • 2026/05/10
  • Category:
  • フェンダージャパン製ストラトキャスターのジャック交換・セットアップです。

    Aシリアルのモデルです。

    長年倉庫に閉まっていたとの事で各所が汚れています。

    ジャック不良があるので新品に交換しましたが音は安定して出ております。
    動作確認+調整してみて使えるかチェックしたいとの事でセットアップしてみましたが特に問題無さそうです。

    また音が非常に良い個体で、当時は数万円でかなり良い個体が普通に購入できた良い時代です。

    別にフェンダージャパンの初期シリアルだからとか関係無く2000年代辺りまでのフェンダージャパンの数万円モデルでもかなり良いのでお勧めです。

    ありがとうございました♪


    This is a jack replacement and setup for a Fender Japan Stratocaster.

    It’s an A-serial model.

    It had been stored in a warehouse for many years, so it’s dirty in various places.

    The jack was faulty, so I replaced it with a new one, and the sound is now stable.
    The owner wanted me to test the functionality and adjust it to see if it was usable, so I performed a setup, and it seems to be working fine.

    It’s also a guitar with excellent tone. Back then, it was a great era when you could easily buy a really good Fender Japan model for just a few tens of thousands of yen.

    Regardless of whether it’s an early Fender Japan serial number or not, even the Fender Japan models from around the 2000s that cost a few tens of thousands of yen are quite good, so I highly recommend them.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    PXL_20260225_082417043
  • BACCHUS TACTICS-STD/RSM テレキャスター ペグ交換&ナット交換&フレットサイド処理&配線直し MusicLily PU

  • 2026/05/08
  • Category:
  • PXL_20260218_110104427

    バッカス製の低価格帯モデル、テレキャスターのペグ交換・ナット交換・フレットサイド処理・配線直しです。

    お客様持ち込みのMusicLilyのPUと電装パーツにグレードアップです。

    ペグをGOTOH製の同型に交換しました。

    ナット材も持ち込みでMusicLily牛骨ナットに交換です。
    こちらはネット上で無加工で付く様な情報があるそうですが、加工が必要になりますのでご注意下さい。

    約23000円のモデルですが基本的なポテンシャルはあり、こうしたグレードアップを行う事で20~30万円台のギターになると思います。

    フロントのサウンドはGibson系に近くなり、ブーミー傾向をややスッキリさせた程好い太さです。
    またこのPUはギブソン製のP-90と違いポールピース高が大きく下げる調整できるのが利点です。
    ギブソン製P-90はポールピース高を下げれる限度が少ないので、各弦の音量調整で不都合が起き易いです。
    音も良い上にポールピース高の自由度が高いので、安物PUながらMusicLilyのPUはお勧めです。

    リアはギラギラしない、通常のテレよりハイ落ち感はあるがその代わり音が太い傾向なのでリアがうるさく感じる際の交換にお勧め機種です。
    低価格PUでも非常に使えるサウンドなので、やはり時代は安物でも使える時代になりました。

    ありがとうございました♪


    This is a Bacchus budget-friendly model—a Telecaster—that underwent tuner and nut replacements, fretboard finishing, and rewiring.

    We upgraded it with a MusicLily pickup and electronic components provided by the customer.

    We replaced the tuners with matching GOTOH models.

    We also replaced the nut with a MusicLily cowbone nut provided by the customer.
    Please note that while some online sources claim this nut fits without modification, it actually requires some adjustment.

    Although this is a model priced at around 23,000 yen, it has solid basic potential. With these upgrades, I believe it now rivals guitars in the 200,000 to 300,000 yen range.

    The front pickup’s sound is now closer to a Gibson-style tone, with a nice, full body that’s been slightly cleaned up from its original boomy tendency.
    Another advantage of this pickup, unlike the Gibson P-90, is that the pole piece height can be significantly lowered.
    With the Gibson P-90, the pole piece height can only be lowered to a limited extent, which often causes issues when adjusting the volume balance between strings.
    With great sound and high flexibility in pole piece height adjustment, I highly recommend MusicLily’s pickups, even though they’re budget-friendly.

    The bridge pickup isn’t overly bright; while it has a slightly reduced high-end response compared to a standard Tele, it tends to have a fuller tone. This makes it a great replacement option if you find the stock bridge pickup too harsh.
    Even budget pickups can deliver a very usable sound these days—it really shows that we’ve entered an era where even affordable gear can be top-notch.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260320_085552882
  • 電源ケーブル製作 BELDEN 19364 + FURUTECH FI-11 FI-C15

  • 2026/05/07
  • Category:
  • PXL_20260320_083034376

    電源ケーブルの製作依頼です。

    ベルデン19364にフルテック製プラグFI-11とFI-C15のセットです。

    私の環境でも電源ケーブルは19364を使用しているので、動作チェックしてみた所プラグだけでも音が明るく硬めな音になる印象です。
    こちらはマリンコ製プラグと非メッキコネクタで作ってますが、メッキ物は高域が強調される様な音に変化します。

    ありがとうございました♪


    I’d like to request a custom power cable.

    I’d like a set consisting of Belden 19364 cable with Fulltec FI-11 and FI-C15 plugs.

    Since I’m currently using 19364 cable in my own setup, I tested it out and found that even just the plugs alone give the sound a brighter, slightly harsher tone.
    I’ve made cables using Marinko plugs and unplated connectors, but when using plated connectors, the sound shifts to emphasize the high frequencies.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260319_132200476
  • Gibson FlyingV セットアップ 左利き

  • 2026/05/06
  • Category:
  • ギブソン製フライングVのセットアップです。

    大きく順反りして弦高が高い状態です。

    こうした状態でサドルで弦高調整するのはNGです。
    まずはネックの反りを調整した上でサドルで弦高を調整しないと大体は「弦高が高いのに音が詰まる」様な状態になります。

    反りを調整し弾き易い状態に仕上げる事ができました。

    ありがとうございました♪


    Here is the setup for a Gibson Flying V.

    The neck has a significant forward bow, resulting in high string action.

    In this condition, adjusting the string height at the saddle is not recommended.
    If you don’t first correct the neck bow and then adjust the string height at the saddle, you’ll likely end up with a situation where the strings are high but the sound is muffled.

    We were able to correct the bow and get the guitar into a comfortable playing condition.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260217_102109501
  • PRS Custom24 フレット交換&ポット交換

  • 2026/05/05
  • Category:
  • PRS Custom24のフレット交換・ポット交換です。

    お客様の要望でステンレスフレットに交換です。

    ボリュームポットのガリで交換しました。

    ニッケルシルバーからステンレスフレットに交換すると音が硬くなります。

    昔は音が「キンキン」すると言われていましたが、近年のステンレスフレットは金属の材質が変わったのかあまりキンキンはしないがハイが痛い傾向よりもミドルが硬い傾向になっています。
    ローズ指板がエボニー指板になった様な硬さが出る音になります。

    実際に削ってても分かりますが、昔よりも金属粒子が大きい?のか、手に伝わる感覚なので言葉にするのは難しいですがステンレスフレットは硬くて削れ難いとは言え昔はサクサクと乾いた削れ具合だったと思うのですが、近年のステンレスフレットはゴリゴリとした粒子が大きく粘りがある金属になっている気がします。

    その辺りが音に影響が出ていると思います。
    昔よりは音の痛みが出ない分、音の面ではステンレスフレットも使用し易い事になったと思いますので交換時の参考にして下さい。

    ありがとうございました♪


    This is a fret and pot replacement on a PRS Custom24.

    At the customer’s request, we replaced the frets with stainless steel ones.

    We also replaced the volume pot due to a scratchy sound.

    Switching from nickel silver to stainless steel frets makes the tone harder.

    In the past, people used to say the sound was “ringy,” but with recent stainless steel frets—perhaps due to a change in the metal composition—they don’t sound quite as ringy; instead of having piercing highs, the midrange tends to be harder.
    The sound takes on a hardness similar to that of an ebony fingerboard instead of a rosewood one.

    You can tell just by filing them—perhaps the metal particles are larger than they used to be? It’s hard to put into words since it’s a sensation transmitted through the hands, but while stainless steel frets are hard and difficult to file, I recall that in the past they filed away crisply and dryly. However, I feel that recent stainless steel frets have larger, gritty particles and a more viscous texture.

    I believe this is what’s affecting the sound.
    Since they don’t produce as much harshness as they used to, I think stainless steel frets have become easier to use in terms of sound, so please keep this in mind when replacing them.

    Thank you very much♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





    PXL_20260221_112402931
  • HARLEY BENTON TE-90QM セットアップ

  • 2026/05/03
  • Category:


  • ハーレーベントン製TE-90QMのセットアップです。

    海外から自分で購入しないと手に入らないメーカーですが、低価格帯ながら非常に良いモデルです。
    もしくはメルカリ・ヤフオクに転売されている物を買うしかありません。

    調整してみると音が非常に良く、約36000円+送料+関税で約5万円程度になります。
    5~6万円と考えても非常に良いギターで、音質は良く弾き易いです。

    ナット高がやや高い・フレットサイド処理は甘い等と低価格帯あるあるな箇所はありますが弾けないレベルではありません。

    かなり価格破壊しているモデルですので、低価格帯で良いギターをお探しの方にお勧め機種です。

    ありがとうございました♪


    Here is the setup for the Harley Benton TE-90QM.

    This is a brand you can only get by purchasing directly from overseas, but despite being in the lower price range, it’s an excellent model.
    Alternatively, your only option is to buy one resold on Mercari or Yahoo Auctions.

    After tuning it, the sound is fantastic. The total cost comes to about 50,000 yen, including the base price of roughly 36,000 yen plus shipping and customs duties.
    Even at 50,000 to 60,000 yen, it’s a fantastic guitar—it sounds great and is easy to play.

    While it has some typical low-end issues, such as a slightly high nut height and rough fret edges, it’s by no means unplayable.

    Since this model is a real bargain, I highly recommend it to anyone looking for a good guitar in the lower price range.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar





BLOG CATEGORY

ARCHIVE