タグ別アーカイブ: セットアップ

    PXL_20260319_132200476
  • Gibson FlyingV セットアップ 左利き

  • 2026/05/06
  • Category:
  • ギブソン製フライングVのセットアップです。

    大きく順反りして弦高が高い状態です。

    こうした状態でサドルで弦高調整するのはNGです。
    まずはネックの反りを調整した上でサドルで弦高を調整しないと大体は「弦高が高いのに音が詰まる」様な状態になります。

    反りを調整し弾き易い状態に仕上げる事ができました。

    ありがとうございました♪


    Here is the setup for a Gibson Flying V.

    The neck has a significant forward bow, resulting in high string action.

    In this condition, adjusting the string height at the saddle is not recommended.
    If you don’t first correct the neck bow and then adjust the string height at the saddle, you’ll likely end up with a situation where the strings are high but the sound is muffled.

    We were able to correct the bow and get the guitar into a comfortable playing condition.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260221_112402931
  • HARLEY BENTON TE-90QM セットアップ

  • 2026/05/03
  • Category:


  • ハーレーベントン製TE-90QMのセットアップです。

    海外から自分で購入しないと手に入らないメーカーですが、低価格帯ながら非常に良いモデルです。
    もしくはメルカリ・ヤフオクに転売されている物を買うしかありません。

    調整してみると音が非常に良く、約36000円+送料+関税で約5万円程度になります。
    5~6万円と考えても非常に良いギターで、音質は良く弾き易いです。

    ナット高がやや高い・フレットサイド処理は甘い等と低価格帯あるあるな箇所はありますが弾けないレベルではありません。

    かなり価格破壊しているモデルですので、低価格帯で良いギターをお探しの方にお勧め機種です。

    ありがとうございました♪


    Here is the setup for the Harley Benton TE-90QM.

    This is a brand you can only get by purchasing directly from overseas, but despite being in the lower price range, it’s an excellent model.
    Alternatively, your only option is to buy one resold on Mercari or Yahoo Auctions.

    After tuning it, the sound is fantastic. The total cost comes to about 50,000 yen, including the base price of roughly 36,000 yen plus shipping and customs duties.
    Even at 50,000 to 60,000 yen, it’s a fantastic guitar—it sounds great and is easy to play.

    While it has some typical low-end issues, such as a slightly high nut height and rough fret edges, it’s by no means unplayable.

    Since this model is a real bargain, I highly recommend it to anyone looking for a good guitar in the lower price range.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260215_104804585
  • Harley Benton TE-90QM セットアップ

  • 2026/04/30
  • Category:
  • ハーレーベントン製TE-90QMのセットアップです。

    新品で購入との事ですが特に問題無く仕上がりました。

    音がタイトで煌びやかで、見た目とは違いモダン系な音がするギターです。
    見た目的にはヴィンテージ系、雑味が多い古い音が鳴ってきそうですがかなり真逆なサウンドです。

    レンジが狭く聴こえは良いが物足りなく感じる為、PU交換で化けるギターかもしれません。

    低価格帯的な、電装パーツを変えれば良くなるかなって感覚のギターです。

    ありがとうございました♪


    Here is the setup for the Harley Benton TE-90QM.

    I was told it was purchased brand new, and the setup went off without a hitch.

    The tone is tight and sparkling; despite its vintage appearance, it has a surprisingly modern sound.
    Visually, it looks vintage and seems like it would produce a rough, old-school sound, but the actual tone is quite the opposite.

    The dynamic range feels a bit narrow—it sounds good but leaves something to be desired—so this might be a guitar that really comes into its own with a pickup swap.

    It’s the kind of guitar you’d expect to find in the lower price range, where you get the feeling that swapping out the electronics might make it sound better.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260206_094352778
  • J.W.Black テレキャスター ブリッジ交換 Mastery

  • 2026/04/27
  • Category:
  • PXL_20260206_090135219

    J.W.Black製テレキャスターのジャック交換です。

    Masteryに交換です。現代的なブリッジです。
    こちらは弦が3本乗るサドルが2個で構成されるブリッジになり、傾斜を付ける事でオクターブ位置を調整します。

    交換後は音が太くなり分離も良くなりました。

    アコギっぽいニュアンスがするテレキャスターで非常に良い個体です。

    ありがとうございました♪


    Replacing the jack on a J.W. Black Telecaster.

    I’m upgrading it to a Mastery bridge—a modern-style bridge.
    This bridge features two saddles, each supporting three strings, and the octave position is adjusted by tilting the saddles.

    After the replacement, the tone became fuller and the separation improved.

    It’s a fantastic Telecaster with a touch of acoustic guitar character.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260131_120124143
  • Gibson CustomShop レスポールカスタム ポット交換

  • 2026/04/24
  • Category:
  • ギブソンカスタムショップ製レスポールカスタムのポット交換です。

    ノブを接着剤で付けてみたらポットが回らなくなったとの事で持ち込まれました。

    ノブが上手く付かない場合は接着剤を使用しないで下さい。
    ポットは消耗品の為、交換する事も考えたら交換時に困難になります。

    接着剤が垂れてポットのナットまで固まっており、その上でナットが斜めに入って無理矢理溝に噛んでいる事から外れない状態(過去に交換していない箇所)です。

    ですのでコントロール側からポットを壊して外し、新品に交換する事で元通りに復元する事ができました。

    ありがとうございました♪


    Pot replacement on a Gibson Custom Shop Les Paul Custom.

    The customer brought it in because the knobs wouldn’t turn after trying to attach them with adhesive.

    Please do not use adhesive if the knobs won’t fit properly.
    Since pots are consumable parts, using adhesive makes replacement difficult later.

    Adhesive had dripped and hardened all the way to the pot’s nut. The nut was then forced into the groove at an angle, making it impossible to remove (this was a previously unreplaced section).

    Therefore, we removed the pot by breaking it from the control side and replaced it with a new one, restoring it to its original condition.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260213_125412410
  • FenderCustomShop ストラトキャスター セットアップ

  • 2026/04/20
  • Category:
  • フェンダーカスタムショップ製ストラトキャスターのセットアップです。

    状態良く調整は特に問題ありませんでした。

    音がモッサリ系で50年代モデルの様子です。

    音が柔らかく雑味が多いので現行品でもヴィンテージギターの様なニュアンスが出せるモデルかと思います。

    ありがとうございました♪


    Here is the setup for a Fender Custom Shop Stratocaster.

    It was in good condition and required no major adjustments.

    The tone has a mellow, mellow character, typical of a ’50s model.

    With its soft tone and rich, warm character, I believe this model can produce a vintage-style sound even though it’s a modern instrument.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260206_113616068
  • Musicman LUKE 4 ポット交換&セットアップ

  • 2026/04/15
  • Category:
  • PXL_20260206_105832088

    ミュージックマン製ルーク4のポット交換です。

    2026年に発売した新モデルですが早速トラブルが起きた様子です。

    音が異常に小さく、スイッチポットのプッシュ/プッシュ式ポットが壊れて切り替えができない状態です。

    内部をチェックしてみるとポットに付いてるプリント基板部分にトラブルが起きている様子です。
    薄い基盤を曲げてハンダ付けされておりますが、この曲がった部分で基盤の断線かハンダ不良により通電不良トラブルが起きてます。

    またスイッチポットでプッシュ/プッシュ式は非常に壊れ易いので使用はお勧めできません。

    お客様の持ち込みでミュージックマン純正ポット交換で対処しました。
    こちらは電装系が基盤タイプになるので、交換時はシャフトが長い専用のポットが必要になるので要注意です。
    市販品のスイッチポットだとシャフトが短く付ける事ができません。
    シャフトが長いスイッチポットじゃないと付かない仕様です。

    またネックがセンターズレしている状態です。
    ネックポケットがかなりタイトであまり修正できませんが、実際にセンターが少しズレて製造されているようにも見えます。
    約80万円するモデルですが、近年は高額でも作りに気になる所がある個体があったりします。

    特に問題無く使用できる様になりましたがスイッチポットのプッシュ/プッシュ式だけは同じ様に壊れる可能性があるので、予備のスイッチポットを沢山買って持っておく事をお勧めします。

    ありがとうございました♪


    Replacing the pots on a Music Man Luke 4.

    Although this is a new model released in 2026, it appears to have encountered issues right away.

    The volume is abnormally low, and the push/push-type switch pot is broken, making it impossible to switch between settings.

    Upon inspecting the interior, it appears there is an issue with the printed circuit board attached to the pot.
    The thin board is bent and soldered, but a break in the circuit or a soldering defect at this bent section is causing a power supply failure.

    Additionally, push-push switch pots are extremely prone to failure, so I do not recommend using them.

    The customer brought the guitar in, and we resolved the issue by replacing it with a genuine Music Man pot.
    Since the electrical system uses a PCB-based design, please note that a special pot with a long shaft is required for replacement.
    Standard off-the-shelf switch pots have shafts that are too short to fit.
    It is designed to only accept switch pots with a long shaft.

    Additionally, the neck is off-center.
    The neck pocket is quite tight, so there isn’t much room for adjustment, but it actually appears as though the instrument was manufactured with the center slightly misaligned.
    Although this is a model that costs around 800,000 yen, even with high-priced instruments these days, there are individual units where the craftsmanship leaves something to be desired.

    The guitar is now fully functional with no issues, but since the push-push switch pot is prone to breaking again, I recommend purchasing and keeping a large supply of spare switch pots on hand.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260207_130306643
  • Charvel DST-1ST ランダムスター セットアップ

  • 2026/04/13
  • Category:
  • シャーベル製ランダムスターのセットアップです。

    順反りし弦高が高い状態です。また正しく調整ができておりません。

    Dチューナーが付いてますがザグリに当たるのでややネック側にフロイドローズを傾けて調整しました。
    本来ならDチューナーを付ける際は専用のザグリが必要になります。

    EMGが乗っており歪み時も音がタイトでメタル曲にはかなり合うサウンドです。

    ありがとうございました♪


    Here is the setup for the Shaber Random Star.

    The neck is bowing outward, and the string action is high. Additionally, it has not been properly adjusted.

    Although it comes with a D-tuner, it was hitting the cutout, so I adjusted the Floyd Rose by tilting it slightly toward the neck.
    Normally, a dedicated cutout is required when installing a D-tuner.

    It’s equipped with EMG pickups, and the sound remains tight even when distorted, making it a great fit for metal songs.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260131_104251032
  • PRS SE SANTANA Custom24 ナット溝切り調整&セットアップ

  • 2026/04/06
  • Category:
  • PRS SE製サンタナモデルCustom24のナット溝切り調整・セットアップです。

    チューニングが狂い易いとの事で持ち込まれました。

    ナット溝切り調整を行い調整しました。

    フロントはギブソンよりもすっきり傾向のサウンド、リアは歪み音が非常に良い個体です。

    電装パーツはノーマル状態ですが明らか他のSE製と比べ音が違う様に聴こえます。
    アーティストモデルの特別なPUでも付いてる?のか、明らかサウンドは他の個体より段違いに良かったです。

    ありがとうございました♪


    Nut Slot Adjustment and Setup for PRS SE Santana Model Custom 24.

    Brought in due to frequent tuning instability.

    Performed nut slot adjustment and fine-tuned the setup.

    The front pickup has a cleaner sound than typical Gibsons, while the rear pickup produces excellent distorted tones.

    Though the electronics are stock, it clearly sounds different from other SE models.
    Could it be a special artist model pickup? Either way, the sound quality was noticeably superior to other units.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




    PXL_20260203_072809799
  • Moon PGM ストラトキャスター ナット交換&フレットすり合わせ

  • 2026/04/01
  • Category:
  • ムーン製PGM期のストラトキャスターのナット交換・フレットすり合わせです。

    80年代製の物で長年の消耗がある状態です。

    ナットを交換しフレットをすり合わせ、正常な状態に仕上げました。

    音が太く、存在感があるのでアンサンブルで抜けが良さそうな個体です。
    当時のMOON製は評価が高い理由もよく分かりました。
    Fender等を良い方向に改良したストラトと思います。

    ありがとうございました♪


    Nut replacement and fret leveling on a Moon-made PGM-era Stratocaster.

    This is an 80s model showing significant wear from years of use.

    We replaced the nut and leveled the frets, restoring it to proper condition.

    It has a thick, present sound that should cut through well in an ensemble.
    It’s easy to see why Moon-made guitars from that era are so highly regarded.
    I consider it a Strat that improves upon models like Fender in positive ways.

    Thank you very much! ♪


    〒114-0014 東京都北区田端1-21-3 エーデルワイス101

    ギターリペア工房 Draw a New Sound

    東京都 山手線 田端から徒歩2分 どこよりも早いリペア早期仕上げ対応可能のリーズナブル料金&丁寧な作業のギターリペアショップです♪

    ●ホームページ Draw a New Sound

    ●YouTubeではブログでは語られない裏話からギターの作り方まで掲載中! 
    マイチャンネル YouTubeチャンネル

    ●ツイッター DNS_Guitar




BLOG CATEGORY

ARCHIVE